Refer to
IAC, Engine Oil Level, Engine Oil Pressure, EGR, EVAP Vent
.
Circuit Description
Output driver modules (ODMs) are used by the Powertrain Control Module (PCM) in order to turn ON many of the current-driven devices that are needed to control various engine and transmission functions. Each ODM is capable of controlling up to 7 separate outputs by applying ground to the device which the PCM is commanding ON. Unlike the quad driver modules (QDMs) used in prior model years, ODMs are capable of diagnosing each output circuit individually. DTC P0449 set indicates that an improper voltage level has been detected on the output circuit which controls the EVAP canister vent valve.
Conditions for Running the DTC
| • | The ignition is ON. |
| • | The system voltage is between 9.0--18.0 volts. |
Conditions for Setting the DTC
| • | An improper voltage level has been detected on the output circuit which controls the EVAP canister vent solenoid valve. |
| • | The above condition is present for at least 30 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using a scan tool. |
Diagnostic Aids
Inspect for the following:
| • | Poor connection at the PCM--Inspect harness connectors for: |
| - | Backed-out terminals |
| - | Improper mating |
| - | Broken locks |
| - | Improperly-formed or damaged terminals |
| - | Faulty terminal-to-wire connections |
| • | A damaged harness--Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the PCM, turn the ignition ON and observe a voltmeter connected between the solenoid control circuit and ground at the PCM harness connector while moving connectors and wiring harnesses related to the solenoid. A change in voltage will indicate the location of the malfunction. |
Review the Failure Records vehicle mileage since the diagnostic test last failed. This may help to determine how often the condition that caused the DTC to be set occurs.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
The Powertrain On-Board Diagnostic (OBD) System Check prompts you to complete some basic checks and to store the Freeze Frame and Failure Records data on the scan tool.
-
Listen for an audible click when the vent solenoid operates. Command both the ON and OFF states. Repeat the commands as necessary.
-
This step tests for voltage at the feed side of the solenoid.
-
This step verifies that the PCM is providing ground to the solenoid.
-
This step tests if a ground is constantly being applied to the solenoid.
-
The PCM uses electrically erasable programmable read only memory (EEPROM). When you replace the PCM, the new PCM must be programmed.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | Go to Step 2 | ||
Does the valve turn ON and OFF with each command? | -- | Go to Diagnostic Aids | Go to Step 3 | |
Does the test lamp illuminate? | -- | Go to Step 4 | Go to Step 10 | |
Does the test lamp turn ON and OFF with each command? | -- | Go to Step 8 | Go to Step 5 | |
Does the test lamp remain illuminated with each command? | -- | Go to Step 7 | Go to Step 6 | |
6 | Test the control circuit of the solenoid for a short to voltage or an open. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
7 | Test the control circuit of the solenoid for a short to ground. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
8 | Inspect for faulty connections at the valve. Refer to Connector Repairs and Testing for Intermittent Conditions and Poor Connections in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 11 |
9 | Inspect for faulty connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
10 | Repair the feed circuit of the valve. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 13 | -- |
11 | Replace the valve. Refer to Evaporative Emission Vent Valve Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- |
|
Important: The replacement PCM must be programmed. Replace the PCM. Refer to Powertrain Control Module Replacement/Programming .Did you complete the replacement? | -- | Go to Step 13 | -- | |
13 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
