GM Service Manual Online
For 1990-2009 cars only

Cooling System Draining and Filling Static Fill-LE5, L61

Special Tools

J 26568 Coolant and Battery Fluid Tester

Draining Procedure


    Object Number: 1718778  Size: SH

    Warning: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling system will release scalding fluid and steam under pressure if radiator cap or surge tank cap is removed while the engine and radiator are still hot.

  1. Remove the coolant pressure cap.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  3. Place a drain pan under the right side lower radiator mount.

  4. Object Number: 877653  Size: SH
  5. Open the radiator drain cock.
  6. Drain the cooling system.

  7. Object Number: 964352  Size: SH
  8. If a complete block drain is required, place a drain pan under the water pump drain.
  9. Remove the water pump drain plug.
  10. Drain the cooling system.
  11. Inspect the appearance of the engine coolant for discoloration:
  12. • Discolored--Follow the flush procedure. Refer to Coolant System Flushing.
    • Normal in appearance--Follow the filling procedure.

Filling Procedure

    Caution: The procedure below must be followed. Improper coolant level could result in a low or high coolant level condition, causing engine damage.


    Object Number: 877653  Size: SH
  1. Close the radiator drain cock by hand.
  2. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 964352  Size: SH
  3. Install the water pump drain plug (1) if removed during the draining process.
  4. Tighten
    Tighten the plug to 22 N·m (16 lb in).

  5. Lower the vehicle.
  6. Note: Use a 50/50 mixture of DEX-COOL antifreeze and clean, drinkable water. It is necessary to maintain the coolant level near the cold fill line on the surge tank to insure all the air has been purged from the cooling system.

  7. Slowly add a mixture of 50/50 DEX-COOL antifreeze and deionized water to the cooling system until the coolant level reaches and maintains slightly above the cold fill line on the surge tank. Refer to Approximate Fluid Capacities.

  8. Object Number: 1718778  Size: SH
  9. Install the coolant pressure cap.
  10. Start the engine.
  11. Run the engine at 2,000-2,500 RPM for 3 minutes.
  12. Allow the engine to idle for 30 seconds.
  13. Shut the engine off.
  14. Top off the coolant as necessary.
  15. Fill the coolant reservoir to the cold fill line.
  16. Inspect the cooling system for leaks.
  17. Inspect the concentration of the coolant mixture using J 26568 .
  18. Rinse away any excess coolant from the engine and the engine compartment.

Cooling System Draining and Filling Static Fill-LNF

Draining Procedure

    Warning: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling system will release scalding fluid and steam under pressure if radiator cap or surge tank cap is removed while the engine and radiator are still hot.

    Note: Draining the cooling system with the pressure cap installed will syphon the coolant from the overflow tank.


    Object Number: 2070585  Size: SH
  1. Remove the pressure cap (1) from the radiator fill tube.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.

  3. Object Number: 1696009  Size: SH
  4. Place a drain pan under the right side lower radiator mount.
  5. Open the radiator drain cock.

  6. Object Number: 1959149  Size: SH
  7. Drain the cooling system.
  8. If a complete block drain is required, place a pan under the water pump drain.
  9. Remove the water pump drain plug (1).
  10. Drain the cooling system.
  11. Inspect the appearance of the engine coolant for discoloration:
  12. • Discolored--Follow the flush procedure. Refer to Coolant System Flushing.
    • Normal in appearance--Follow the filling procedure.

Filling Procedure


    Object Number: 1696009  Size: SH

    Caution: The procedure below must be followed. Improper coolant level could result in a low or high coolant level condition, causing engine damage.

  1. Close the radiator drain cock by hand.
  2. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1959149  Size: SH
  3. Install the water pump drain plug if removed during the draining process (1).
  4. Tighten
    Tighten the drain plug to 22 N·m (16 lb ft).

  5. Lower the vehicle.
  6. Note: Use a 50/50 mixture of DEX-COOL antifreeze and clean, drinkable water.

  7. Slowly add a mixture of 50/50 DEX-COOL antifreeze and clean, drinkable water to the cooling system until the coolant level reaches the top of the radiator fill tube and stabilizes.
  8. Slowly add a mixture of 50/50 DEX-COOL antifreeze and clean, drinkable water to the overflow bottle until the level reaches the specified mark.
  9. Start the engine.

  10. Object Number: 2070585  Size: SH
  11. Install the pressure cap (1).
  12. Run the engine at idle for 5 minutes in PARK (P) (Automatic) or NEUTRAL (N) (Manual) with the parking brake on.
  13. Turn off the engine and allow it to cool and the system pressure to decrease.
  14. Remove the surge tank cap (1).
  15. Add coolant to the cooling system until the level reaches the top of the radiator fill tube stabilizes.
  16. Install the surge tank cap (1).
  17. Run the engine at idle for an additional 5 minutes.
  18. Turn off the engine and allow it to cool.
  19. Inspect the cooling system for leaks.
  20. Rinse away any excess coolant from the engine and the engine compartment.

Cooling System Draining and Filling GE 47716 Fill

Special Tools

    • J 26568 Coolant and Battery Fluid Tester
    • J 42401 Radiator Pressure Adapter
    • GE-47716 Vac N Fill Coolant Refill Tool

Draining Procedure


    Object Number: 873722  Size: SH

    Warning: To avoid being burned, do not remove the radiator cap or surge tank cap while the engine is hot. The cooling system will release scalding fluid and steam under pressure if radiator cap or surge tank cap is removed while the engine and radiator are still hot.

  1. Remove the pressure cap.
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
  3. Place a drain pan under the right side lower radiator mount.

  4. Object Number: 877653  Size: SH
  5. Open the radiator drain cock.
  6. Drain the cooling system.

  7. Object Number: 893494  Size: SH
  8. If a complete block drain is required, place a drain pan under the water pump drain.
  9. Remove the water pump drain plug (1).
  10. Drain the cooling system.
  11. Inspect the appearance of the engine coolant for discoloration:
  12. • Discolored--Follow the flush procedure. Refer to Coolant System Flushing.
    • Normal in appearance--Follow the filling procedure.

Vac-N-Fill Procedure


    Object Number: 877653  Size: SH

    Caution: The procedure below must be followed. Improper coolant level could result in a low or high coolant level condition, causing engine damage.

  1. Close the radiator drain cock by hand.

  2. Object Number: 1617435  Size: SH

    Note: To prevent boiling of the coolant/water mixture in the vehicle’s cooling system, do not apply vacuum to a cooling system above 49° C (120° F). The tool will not operate properly when the coolant is boiling.

  3. Install J-42401-2 into the surge tank fill neck.
  4. Install J-42401-3 to the surge tank fill neck.
  5. Attach the Vac N Fill cap to the J-42401-3.

  6. Object Number: 1617436  Size: SH
  7. Attach the vacuum gage assembly to the Vac N Fill cap.

  8. Object Number: 1617437  Size: SH
  9. Attach the fill hose to the barb fitting on the vacuum gage assembly.
  10. Ensure that the valve is closed.


    Object Number: 1617438  Size: SH

    Note: Use a 50/50 mixture of DEX-COOL antifreeze and clean, drinkable water.

    Always use more coolant than necessary. This will eliminate air from being drawn into the cooling system.

  11. Pour the coolant mixture into the graduated reservoir.
  12. Place the fill hose in the graduated reservoir.
  13. Note: Prior to installing the vacuum tank onto the graduated reservoir, ensure that the drain valve located on the bottom of the tank is closed.

  14. Install the vacuum tank on the graduated reservoir with the fill hose routed through the cut-out area in the vacuum tank.

  15. Object Number: 1617439  Size: SH
  16. Attach the venturi assembly to the vacuum tank.

  17. Object Number: 1617440  Size: SH
  18. Attach a shop air hose to the venturi assembly.
  19. Ensure the valve on the venturi assembly is closed.


    Object Number: 1617441  Size: SH
  20. Attach the vacuum hose to the vacuum gage assembly and the vacuum tank.

  21. Object Number: 1617442  Size: SH
  22. Open the valve on the venturi assembly. The vacuum gage will begin to rise and a hissing noise will be present.

  23. Object Number: 1617443  Size: SH
  24. Continue to draw vacuum until the needle stops rising. This should be 610-660 mm Hg (24-26 in Hg).
  25. Cooling hoses may start to collapse. This is normal due to vacuum draw.

  26. To aid in the fill process, position the graduated reservoir above the coolant fill port.

  27. Object Number: 1617446  Size: SH
  28. Slowly open the valve on the vacuum gage assembly. When the coolant reaches the top of the fill hose, close the valve. This will eliminate air from the fill hose.
  29. Close the valve on the venturi assembly.
  30. If there is a suspected leak in the cooling system, allow the system to stabilize under vacuum and monitor for vacuum loss.
  31. If vacuum loss is observed, refer to Loss of Coolant.

  32. Open the valve on the vacuum gage assembly. The vacuum gage will drop as coolant is drawn into the system.

  33. Object Number: 1617448  Size: SH
  34. Once the vacuum gage reaches zero, close the valve on the vacuum gauge assembly and repeat steps 10-16.
  35. Detach the Vac N Fill cap from the vehicle's coolant fill port.
  36. Add coolant to the system as necessary.
  37. Inspect the concentration of the coolant mixture using J 26568 .
  38. Note: After filling the cooling system, the extraction hose can be used to remove excess coolant to achieve the proper coolant level.

  39. Detach the vacuum hose from the vacuum gage assembly.

  40. Object Number: 1617450  Size: SH
  41. Attach the extraction hose to the vacuum hose.

  42. Object Number: 1617453  Size: SH
  43. Open the valve on the venturi assembly to start a vacuum draw.

  44. Object Number: 1617456  Size: SH
  45. Use the extraction hose to draw out coolant to the proper level.
  46. The vacuum tank has a drain valve on the bottom of the tank. Open the valve to drain coolant from the vacuum tank into a suitable container for disposal.