GM Service Manual Online
For 1990-2009 cars only

Special Tools

J 45722 Fuel Sender Lock Ring Wrench

Removal Procedure

Caution: Refer to Gasoline/Gasoline Vapors Caution in the Preface section.

Caution: In order to reduce the risk of fire and personal injury that may result from a fuel leak, always replace the fuel sender gasket when reinstalling the fuel sender assembly.


    Object Number: 1636698  Size: SH
  1. Remove the fuel tank. Refer to Fuel Tank Replacement .
  2. Disconnect the fuel pressure sensor and fuel pump module electrical connectors (1, 4).
  3. Disconnect the fuel tank vent pipe quick connect fittings (2, 3). Refer to Plastic Collar Quick Connect Fitting Service .
  4. Disconnect the fuel tank feed pipe quick connect fitting (5). Refer to Plastic Collar Quick Connect Fitting Service .
  5. Install the J 45722 to the lock ring.

  6. Object Number: 1642096  Size: SH

    Notice: Avoid damaging the lock ring. Use only J-45722 to prevent damage to the lock ring.

    Notice: Do Not handle the fuel sender assembly by the fuel pipes. The amount of leverage generated by handling the fuel pipes could damage the joints.

    Important: Do NOT use impact tools. Significant force will be required to release the lock ring. The use of a hammer and screwdriver is not recommended. Secure the fuel tank in order to prevent fuel tank rotation.

  7. Use the J 45722 and a long breaker-bar in order to unlock the fuel sender lock ring. Turn the fuel sender lock ring in a counterclockwise direction.
  8. Remove the module lock ring.

  9. Object Number: 1636701  Size: SH
  10. Slowly raise the module until the fuel level sensor float arm is just visible. Ensure that the fuel level sensor harness connector clears the tank opening.
  11. Important: When removing the module from the fuel tank, be aware that the module reservoir bowl is full of fuel. The module must be tipped slightly during removal to avoid bending the fuel level sensor float arm.

  12. Tilt the module toward the rear of the fuel tank to allow the level sensor float arm to clear the tank opening. Remove the module from the tank.
  13. Carefully discard the fuel in the module reservoir bowl into an approved fuel container.
  14. Important: DO NOT reuse the old fuel pump module seal.

  15. Remove and discard the fuel pump module seal.

  16. Object Number: 1617750  Size: SH

    Important: 

       • Some lock ring were manufactured with DO NOT REUSE stamped into them. These lock rings may be reused if they are not damaged or warped.
       • Inspect the lock ring for damage due to improper removal or installation procedures. If damage is found, install a NEW lock ring.
       • Check the lock ring for flatness.

  17. Place the lock ring on a flat surface. Measure the clearance between to lock ring and the flat surface using a feeler gage at 7 points.
  18. If the warpage is less than 0.41 mm (0.016 in), the lock ring does not require replacement.
  19. If the warpage is greater than 0.41 mm (0.016 in), the lock ring must be replaced.
  20. If only replacing the module, remove the fuel level sensor. Refer to Fuel Level Sensor Replacement .

Installation Procedure


    Object Number: 1636701  Size: SH
  1. Install a NEW fuel pump module seal onto the fuel tank.
  2. If installing only the module, install the fuel level sensor. Refer to Fuel Level Sensor Replacement .
  3. Important: The reservoir must be tipped slightly during installation to avoid bending the fuel level sensor float arm.

  4. Tilt the module toward the rear of the fuel tank to allow the fuel level sensor float arm to clear the tank opening. Install the module into the fuel tank.
  5. Lower the module assembly into the tank. Ensure that the fuel level sensor harness connector is positioned properly.
  6. Install the module lock ring over the module pipes and electrical harness, and into position on the top of the module.

  7. Object Number: 1642096  Size: SH

    Important: Always replace the fuel sender seal when installing the fuel sender assembly. Replace the lock ring if necessary. Do not apply any type of lubrication in the seal groove.

    Ensure the lock ring is installed with the correct side facing upward. A correctly installed lock ring will only turn in a clockwise direction.

  8. Use the J 45722 in order to install the fuel sender lock ring. Turn the fuel sender lock ring in a clockwise direction.
  9. Remove the J 45722 from the lock ring.

  10. Object Number: 1636698  Size: SH
  11. Connect the fuel tank feed pipe quick connect fitting (5). Refer to Plastic Collar Quick Connect Fitting Service .
  12. Connect the fuel tank vent pipe quick connect fittings (2, 3). Refer to Plastic Collar Quick Connect Fitting Service .
  13. Connect the fuel pressure sensor and fuel pump module electrical connectors (1, 4).
  14. Install the fuel tank. Refer to Fuel Tank Replacement .