GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2001 🢒 Express 🢒 Engine 🢒 Engine Controls - 5.0L and 5.7L 🢒 DTC P0336

Circuit Description

The crankshaft position (CKP) sensor signal indicates the crankshaft speed and position. The CKP sensor is connected directly to the powertrain control module (PCM) and consists of the following circuits:

    • The 12-volt reference circuit
    • The low reference circuit
    • The CKP sensor signal circuit

Conditions for Running the DTC

The engine is cranking or running.

Conditions for Setting the DTC

The powertrain control module (PCM) determines that the CKP sensor signal is out of range for less than 3 seconds.

Diagnostic Aids

Important: 

   • Remove any debris from the PCM module connector surfaces before servicing the PCM module. Inspect the PCM module connector gaskets when diagnosing or replacing the modules. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion into the PCM modules.
   • For any test that requires probing the PCM or a component harness connector, use the J 35616 connector test adapter kit . Using this kit prevents damage to the harness/component terminals. Refer to Connector Repairs in Wiring Systems.

    • The following conditions may cause this DTC to set:
       - Poor connections--Refer to Connector Repairs in Wiring Systems.
       - Crankshaft reluctor wheel damage or improper installation
       - The sensor coming in contact with the reluctor wheel
       - The engine running out of fuel
       - If the crankshaft rotates backwards, this DTC sets. This condition is only with vehicles equipped with a manual transmission. This condition occurs when a vehicle is on an incline, the clutch is released, and an engine stall occurs.
    • Excess crankshaft end play will cause the CKP sensor reluctor wheel to move out of alignment with the CKP sensor. This could result in any one of the following:
       - A no start
       - A start and stall
       - Erratic performance
    • An improperly installed propeller shaft could cause excess crankshaft end play.
    • For an intermittent, refer to Intermittent Conditions .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step verifies that the malfunction is present.

    2.

  2. This step tests for electromagnetic interference (EMI) on the CKP sensor circuits.

    3.

  3. Vertical lines across the face of the sensor could indicate foreign material passing between the CKP sensor and the reluctor wheel. Non-vertical lines across the face of the sensor may indicate a crack in the CKP sensor. Either of these conditions causes this DTC to set.

    4.

  4. Damage to the reluctor wheel would affect the CKP sensor output. To inspect the reluctor wheel, remove the starter and rotate the crankshaft while viewing the reluctor wheel through the CKP sensor hole. If you cannot determine if the reluctor wheel is damaged, the oil pan may have to be removed.

Step

Action

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check-Engine Controls?

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

Important: If DTC P0335 is also set, diagnose DTC P0335 before proceeding with this DTC.

  1. Observe the Freeze Frame/Failure Records data for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text or as close to the Freeze Frame/Failure Records data that you observed.

Does the DTC fail this ignition?

Go to Step 3

Go to Diagnostic Aids

3

  1. Visually and physically inspect all circuits going to the crankshaft position sensor for the following:
    2. • Routed too close to secondary ignition wires or components
    • Routed too close to after-market add on electrical equipment
    • Routed too close to solenoids, relays, and motors
  2. If you find incorrect routing, correct the harness routing.

Did you find and correct the condition?

Go to Step 9

Go to Step 4

4
  1. Inspect for poor connections at the CKP sensor. Refer to Connector Repairs in Wiring Systems.
  2. If you find a poor connection repair the terminal as necessary. Refer to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 5

5
  1. Inspect for poor connections at the PCM for the CKP sensor circuits.
  2. If you find a poor connection repair the terminal as necessary. Refer to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 6

6

  1. Remove the CKP sensor. Refer to Crankshaft Position Sensor Replacement .
  2. Inspect the CKP sensor for signs of damage.
  3. If you find the CKP to be damaged, refer to Crankshaft Position Sensor Replacement .

Did you find and correct the condition?

Go to Step 9

Go to Step 7

7

  1. Inspect the CKP reluctor wheel for damage.
  2. If you find the CKP reluctor wheel damaged, refer to Crankshaft Position Sensor Reluctor Ring Replacement in Engine Mechanical - 5.0L and 5.7L .

Did you find and correct the condition?

Go to Step 9

Go to Step 8

8

Replace the CKP sensor. Refer to Crankshaft Position Sensor Replacement .

Did you find and correct the condition?

Go to Step 9

--

9
  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running this DTC as specified in the supporting text.

Does the DTC run and pass?

Go to Step 10

Go to Step 2

10

With a scan tool, observe the stored information, Capture Info.

Does the scan tool display any DTCs that you have not diagnosed?

Go to Diagnostic Trouble Code (DTC) List

System OK