GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2008 🢒 Equinox 🢒 Preface 🢒 Cautions and Notices 🢒 Battery Negative Cable Replacement

Battery Negative Cable Replacement LNJ

Removal Procedure

Important: 

   • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
   • Always route the replacement cable the same way as the original cable.


    Object Number: 1822394 Size: SH
  1. Remove the battery box. Refer to Battery Box Replacement .
  2. Disconnect the positive and negative battery cable clip (3) from the battery tray support bracket.
  3. Disconnect the positive and negative battery cable clip on the side of the battery tray support bracket.

    4. Object Number: 1822518 Size: SH
  4. Disconnect the negative battery cable electrical connector (7) from the body wiring harness electrical connector (2).
  5. Disconnect the body wiring harness electrical connector (4) from the battery current sensor (5).

    6. Object Number: 1822523 Size: SH
  6. Remove the negative battery cable ground terminal nut from the wheelhouse stud.
  7. Remove the negative battery cable ground terminal from the wheelhouse stud.

    8. Object Number: 1916644 Size: SH
  8. Remove the negative battery cable ground terminal nut (2) from the transaxle stud.
  9. Remove the engine wiring harness ground lead (1) from the stud.
  10. Remove the negative battery cable (3) lead from the stud.

    11. Object Number: 1916156 Size: SH
  11. Remove the battery cable retainer (4) from the transaxle selector cable bracket.
  12. Cut the tape and remove the negative battery cable from the wiring loom.

Installation Procedure

    Object Number: 1916156 Size: SH
  1. Install the negative battery cable to the wiring loom and re-tape the loom.
  2. Install the battery cable retainer (4) to the transaxle selector cable bracket.

    3. Object Number: 1916644 Size: SH
  3. Install the negative battery cable (3) lead to the stud.
  4. Install the engine wiring harness ground lead (1) to the stud.

    5. Notice: Refer to Fastener Notice in the Preface section.

  5. Install the negative battery cable ground terminal nut (2) to the transaxle stud.

    6. Tighten
    Tighten the nut to 45 N·m (33 lb ft).


    Object Number: 1822523 Size: SH
  6. Install the negative battery cable ground terminal to the wheelhouse stud.
  7. Install the negative battery cable ground terminal nut to the wheelhouse stud.

    8. Tighten
    Tighten the nut to 12 N·m (106 lb in).


    Object Number: 1822518 Size: SH
  8. Connect the body wiring harness electrical connector (4) to the battery current sensor (5).
  9. Connect the negative battery cable electrical connector (7) to the body wiring harness electrical connector (2).

    10. Object Number: 1822394 Size: SH
  10. Connect the positive and negative battery cable clip (3) to the battery tray support bracket.
  11. Connect the positive and negative battery cable clip to the side of the battery tray support bracket.
  12. Install the battery box. Refer to Battery Box Replacement .

Battery Negative Cable Replacement LY7

Removal Procedure

Important: 

   • Always use replacement cables that are of the same type, diameter and length of the cables that you are replacing.
   • Always route the replacement cable the same way as the original cable.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection.
  2. Remove the battery box. Refer to Battery Box Replacement.

    3. Object Number: 1822394 Size: SH
  3. Disconnect the positive and negative battery cable clip (3) from the battery tray support bracket.

    4. Object Number: 1822518 Size: SH
  4. Disconnect the negative battery cable electrical connector (7) from the body wiring harness electrical connector (2).
  5. Disconnect the body wiring harness electrical connector (4) from the battery current sensor (5).

    6. Object Number: 1822523 Size: SH
  6. Remove the nut retaining the negative battery cable ground terminal to the wheelhouse stud.

    7. Object Number: 1916167 Size: SH
  7. Remove the bolt (2) retaining the negative battery cable ground terminal to the engine.
  8. Remove the battery cable retainers (1) from the engine.
  9. Cut the tape and remove the negative battery cable from the wiring loom.

Installation Procedure

    Object Number: 1916167 Size: SH
  1. Install the negative battery cable to the wiring loom and re-tape the loom.
  2. Install the battery cable retainers (1) to the engine.

    3. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the negative battery cable ground terminal to the transaxle.

    4. Tighten
    Tighten the negative battery cable ground terminal bolt to 45 N·m (33 lb ft).


    Object Number: 1822523 Size: SH
  4. Install the negative battery cable ground terminal to the wheelhouse stud.

    5. Tighten
    Tighten the ground terminal nut to 12 N·m (106 lb in).


    Object Number: 1822518 Size: SH
  5. Connect the body wiring harness electrical connector (4) to the battery current sensor (5).
  6. Connect the negative battery cable electrical connector (7) to the body wiring harness electrical connector (2).

    7. Object Number: 1822394 Size: SH
  7. Connect the positive and negative battery cable clip (3) to the battery tray support bracket.
  8. Install the battery box. Refer to Battery Box Replacement.
  9. Connect the negative battery cable and install the upper battery box. Refer to Battery Negative Cable Disconnection and Connection.