GM Service Manual Online
For 1990-2009 cars only

Tools Required

    • J 42991 Strut Rod Nut Socket
    • J 45400 Strut Spring Compressor

Removal Procedure


    Object Number: 932520  Size: SH
  1. Install the strut assembly in the J 45400 using the following procedure.
  2. 1.1. Adjust the lower legs of the J 45400 to the lowest possible coil of the spring.
    1.2. Adjust the upper legs of the J 45400 to the highest possible coil of the spring.
    1.3. Inspect the strut assembly to insure hooks on the strut compress legs are properly installed on the spring coils.
    1.4. Verify the strut assembly is parallel with the J 45400 .
  3. Compress the spring enough to unload the upper strut mount.

  4. Object Number: 932545  Size: SH

    Notice: Do not allow the absorber rod to rotate during disassembly/reassembly. Use hand tools to keep the absorber rod from rotating. If air tools are used, and the rod is allowed to rotate, damage to the absorber may occur.

  5. Use the J 42991 or equivalent hand tools to remove the strut shaft nut.

  6. Object Number: 932524  Size: SH

    Important: Leave the spring in the spring compressor.

  7. Lower the strut from the spring assembly.

  8. Object Number: 930279  Size: SH

    Notice: Do not handle the top mount assembly by the plastic portion. Handle the top mount assembly by the metal portion when removing/installing the top mount from/to the strut assembly. Holding the top mount assembly by the plastic portion may loosen the snap fit of the bearing components and cause the bearing to fall apart.

  9. Remove the upper mount assembly, inspect for damage and deterioration. Replace as necessary.
  10. Remove the strut dust shield and inspect for damage and deterioration. Replace as necessary.
  11. Remove the hollow bumper from the strut shaft and inspect for damage and deterioration. Replace as necessary.
  12. Inspect the spring for damage. Replace as necessary.

Installation Procedure


    Object Number: 930279  Size: SH
  1. Extend the strut to its limit of travel.
  2. Install the hollow bumper and dust boot to the strut shaft.

  3. Object Number: 932524  Size: SH

    Important: The tag identifying the spring will be closer to the bottom of the spring. The end of the cold sits up against the tab on the spring seat.

  4. With the spring in the compressor, install the strut into the spring.
  5. Important: The anti-rotation tab on the spring seat must face 180 degrees from the direction that the knuckle bracket points.

  6. Assemble the upper spring seat onto the strut shaft and align the flat with the strut to knuckle mounting bracket.
  7. Notice: Do not handle the top mount assembly by the plastic portion. Handle the top mount assembly by the metal portion when removing/installing the top mount from/to the strut assembly. Holding the top mount assembly by the plastic portion may loosen the snap fit of the bearing components and cause the bearing to fall apart.

    Important: The flat on the metal plate of the top mount assembly must face the same direction of the anti-rotation tab on the spring seat.

  8. Assemble the top mount onto the strut shaft and align the flat 180 degrees from flat on the upper spring seat.

  9. Object Number: 932545  Size: SH
  10. Loosely install the strut shaft nut.
  11. Notice: Refer to Fastener Notice in the Preface section.

    Notice: Do not allow the absorber rod to rotate during disassembly/reassembly. Use hand tools to keep the absorber rod from rotating. If air tools are used, and the rod is allowed to rotate, damage to the absorber may occur.

  12. Hold the strut shaft and use the J 42991 or equivalent hand tools to tighten the shaft while verifying that the upper spring seat flats align with the top mount.
  13. Tighten
    Tighten the strut shaft to 85 N·m (63 lb ft).


    Object Number: 932520  Size: SH
  14. Release the tension on the J 45400 .
  15. Remove the strut assembly from the J 45400 .