This vehicle is equipped with the BOSCH 5.3 antilock braking system.
| • | Antilock Brake System (ABS) |
| • | Dynamic Rear Proportioning (DRP) |
| • | Traction Control System (TCS) (w/NW7) |
| • | Electronic Brake Control Module (EBCM) - The EBCM controls the system functions and detects failures. |
| The EBCM contains the following components are involved in the operation of the above systems: |
| • | System Relay - The system relay is energized when the ignition is ON and no ABS DTCs are present. It supplies battery positive voltage to the solenoid valves and pump motor. |
| • | Vent Tube - The vent tube located in the EBCM connector is an opening to the internal cavity of the EBCM. It allows ventilation of the EBCM internals. |
| • | Brake Pressure Modulator Valve (BPMV) - The BPMV contains the hydraulic valves and pump motor that are controlled electrically by the EBCM. The BPMV uses a 4 circuit configuration with a diagonal split. The BPMV directs fluid from the reservoir of the master cylinder to the left front and right rear wheels and fluid from the other reservoir to the right front and left rear wheels. The diagonal circuits are hydraulically isolated so that a leak or malfunction in one circuit will allow continued braking ability on the other. |
The purpose of the Antilock Brake System (ABS) is to minimize wheel slip during heavy braking. The ABS performs this function by monitoring the speed of each wheel and controlling the brake fluid pressure to each wheel independently during an braking event. This allows the driver to maintain directional stability while minimizing stopping distance.
Valve Assembly (BPMV)
The valve assembly provides brake fluid pressure modulation for each of the individual wheel circuits, as required, during an ABS/traction control system (TCS) event. During an ABS event, the valve assembly can maintain or reduce brake fluid pressure that is applied by the master cylinder. The valve assembly cannot increase pressure beyond what is applied by the master cylinder (driver). The valve assembly contains a motor-driven pump, ABS inlet and outlet valves, as well as TCS prime and isolation valves. With exception of the ABS control module (EBTCM), the valve assembly is not serviceable and should never be disassembled.
The valve assembly is an addition to the four-circuit diagonally-split hydraulic system found on vehicles without ABS.
ABS Control Module (EBCM)
The ABS control module monitors the speed of each wheel to detect wheel slip. If wheel slip is detected, the module commands the appropriate valve positions in the valve assembly to modulate brake pressure in some or all of the hydraulic circuits. This action prevents wheel slip and provides optimum braking. In addition, the ABS control module performs a continuous diagnostic routine to detect malfunctions. If the module detects an electrical malfunction, it can disable ABS/traction control module (TCS)/dynamic rear proportioning (DRP), illuminate the appropriate telltale, and store a Diagnostic Trouble Code (DTC).
The ABS control module contains a solenoid for each ABS/TCS valve it operates and a relay for the solenoid circuit and pump motor circuit respectively. The relays and solenoids are not serviceable.
ABS Operation
During an ABS event, the ABS control module will control the hydraulic pressure in the individual wheel circuits to prevent any wheel from slipping. The control module can decrease or hold hydraulic pressure by energizing the appropriate valve solenoid. A rapid pulsation is felt in the brake pedal and a ticking or popping noise can be heard as control module commands valve solenoids in response to wheel speed changes.
When the ABS control module detects wheel slip, it holds pressure by closing both the inlet valve from the master cylinder and the outlet valve. If pressure hold is not enough to control wheel slip, the ABS control module releases pressure by opening the outlet valve and allowing some pressure bleed-off into the accumulator. The accumulator stores this fluid until the motor-driven pump returns fluid to the master cylinder.
The control module opens the inlet valve to allow master cylinder pressure to the wheel circuits again when no wheel slip is detected.
Traction Control System (TCS)
The Traction Control System (TCS) compares front wheel speeds to rear wheel speeds to determine if drive wheels lose traction. The TCS activates when drive wheel speed exceeds speed of non-drive wheels by a calibrated value. This allows the driver to maintain acceleration and directional stability while accelerating on low traction surfaces.
The TCS limits wheel slip during acceleration when one or more of the drive wheels lose traction. The brake switch must be off for TCS to operate.
The ABS control module monitors wheel speed output and compares drive wheel to non-drive wheel values to detect wheel slip. During a TCS event, the ABS control module sends a requested torque value to the powertrain control module (PCM). The PCM initiates an engine torque reduction routine to slow down the drive wheels. This routine consists of ignition timing reduction, fuel injector cut-off and transmission shift control. The PCM also sends a torque delivered value to the ABS control module. If the engine management routine is insufficient to achieve the desired wheel speed, the ABS control module will then use the TCS isolation valves and prime valves to slow down the drive wheels. The isolation valves close to isolate the wheel circuit from the master cylinder and the prime valves open to allow the motor-driven pump to access master cylinder fluid so it can build pressure to apply the desired brake.
If the ABS control module detects a malfunction, it will disable TCS and will command the body control module (BCM) to turn the TRAC LED Off. The driver can also disable TCS, if desired, by depressing the TRAC switch. When the driver depresses the TRAC switch, the ABS control module will disable TCS and will command the BCM to turn the TRAC LED Off.
Dynamic Rear Proportioning (DRP)
Dynamic rear proportioning (DRP) is an electronic brake proportioning feature that replaces the mechanical proportioning valve in the base brake system. DRP uses existing ABS components to regulate the vehicle's rear brake pressure and provide optimum front-rear brake balance in all braking situations.
