DTC P1863 European and N American Emissions
Circuit Description
The pressure control solenoid (PCS) valves, valves 3, 4, 5, and 6, are precision electronic pressure regulators that control the operation of the clutches, the brakes, and the lock-up clutch.
The valve reduces the system pressure with which the downstream solenoid valves and electrical pressure regulating valves are supplied. It is possible to use smaller solenoid valves as a result. The PCS requires a constant input pressure.
Conditions for Setting the DTC
| • | The output ampere of the PCS 4 is less than 10 milliampere. |
| • | No DTCs P1861 or P1862 are set. |
Action Taken When the DTC Sets
| • | The malfunction indicator lamp (MIL) will illuminate. |
| • | The transmission control module (TCM) will record operating conditions at the time the diagnostic fails. This information will be stored in the Failure Records buffer. |
| • | Adopt Emergency/Substitute mode and constant 4th gear by hydraulic control. |
| • | After the ignition is OFF/ON: 3rd gear by hydraulic control. Possible P, R, and N are also possible. |
| • | The power supply is cut off to the PCS valve. |
Conditions for Clearing the MIL/DTC
| • | The MIL will turn OFF when the malfunction has not occurred after 3 ignition cycles. |
| • | A history DTC will clear after 40 consecutive warm-up cycles without a fault. |
| • | Using a scan tool can clear history DTCs. |
Diagnostic Aids
When DTC P1863 sets, the possible cause of the fault could be the PCS 4 valve.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Automatic Transmission? | -- | Go to Step 2 | |
2 |
Does the PCS 4 change ON/OFF? | -- | Go to Diagnostic Aids | Go to Step 3 |
3 |
Is the resistance within the specified values? | 6 ohms | Go to Step 7 | Go to Step 4 |
4 |
Is the resistance within the specified value? | 0 ohms | Go to Step 6 | Go to Step 5 |
5 |
Did you complete the repair? | -- | System OK | -- |
6 | Replace the PCS 4. Did you complete the replacement? | -- | System OK | -- |
7 |
Is the resistance within the specified value? | 0 ohms | Go to Step 9 | Go to Step 8 |
8 | Repair the transaxle wiring harness for an open. Did you complete the repair? | -- | System OK | -- |
9 | Replace the TCM. Refer to Transmission Control Module Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- |
10 |
Are there any DTCs displayed that have not been diagnosed? | -- | Go to Step 2 | System OK |
DTC P1863 Non European or N American Emissions
Circuit Description
The pressure control solenoid (PCS) valves, valves 3, 4, 5, and 6, are precision electronic pressure regulators that control the operation of the clutches, the brakes, and the lock-up clutch.
The valve reduces the system pressure with which the downstream solenoid valves and electrical pressure regulating valves are supplied. It is possible to use smaller solenoid valves as a result. The PCS requires a constant input pressure.
Conditions for Setting the DTC
| • | The output ampere of the PCS 4 is less than 10 milliampere. |
| • | No DTCs P1861 or P1862 are set. |
Action Taken When the DTC Sets
| • | The hold lamp will blink. |
| • | The transmission control module (TCM) will record operating conditions at the time the diagnostic fails. This information will be stored in the Failure Records buffer. |
| • | Adopt Emergency/Substitute mode and constant 4th gear by hydraulic control. |
| • | After the ignition is OFF/ON: 3rd gear by hydraulic control. Possible P, R, and N are also possible. |
| • | The power supply is cut off to the PCS valve. |
Conditions for Clearing the Hold Lamp/DTC
| • | The hold lamp will turn OFF when the malfunction has not occurred after 3 ignition cycles. |
| • | A history DTC will clear after 40 consecutive warm-up cycles without a fault. |
| • | Using a scan tool can clear history DTCs. |
Diagnostic Aids
When DTC P1863 sets, the possible cause of the fault could be the PCS 4 valve.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check - Automatic Transmission? | -- | Go to Step 2 | |
2 |
Does the PCS 4 change ON/OFF? | -- | Go to Diagnostic Aids | Go to Step 3 |
3 |
Is the resistance within the specified values? | 6 ohms | Go to Step 7 | Go to Step 4 |
4 |
Is the resistance within the specified value? | 0 ohms | Go to Step 6 | Go to Step 5 |
5 |
Did you complete the repair? | -- | System OK | -- |
6 | Replace the PCS 4. Did you complete the replacement? | -- | System OK | -- |
7 |
Is the resistance within the specified value? | 0 ohms | Go to Step 9 | Go to Step 8 |
8 | Repair the transaxle wiring harness for an open. Did you complete the repair? | -- | System OK | -- |
9 | Replace the TCM. Refer to Transmission Control Module Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- |
10 |
Are there any DTCs displayed that have not been diagnosed? | -- | Go to Step 2 | System OK |
