Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Door Lock/Indicator Schematics and Door Control Module Schematics Connector End View Reference: Power Door Systems Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Verify that the power door locks are inoperative from one door or switch. Do the power door locks operate normally? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 | Is the passenger door lock switch the inoperative switch? | Go to Step 4 | Go to Step 6 |
4 | Are both the lock and unlock functions inoperative? | Go to Step 8 | Go to Step 5 |
5 | Is the lock function inoperative? | Go to Step 9 | Go to Step 10 |
6 |
Does the scan tool display Idle? | Go to Step 11 | Go to Step 7 |
7 | Does the scan tool display Lock? | Go to Step 12 | Go to Step 13 |
8 | Test the passenger door lock switch ground circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 14 |
9 | Test the passenger door lock switch lock signal circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 15 |
10 | Test the passenger door lock switch unlock signal circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 15 |
11 | Test the driver door lock switch ground circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 16 |
12 | Test the driver door lock switch unlock signal circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 15 |
13 | Test the driver door lock switch lock signal circuit for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 15 |
14 | Inspect for poor connections at the harness connector of the passenger door lock switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 17 |
15 | Inspect for poor connections at the harness connector of the appropriate door module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 18 |
16 | Inspect for poor connections at the harness connector of the driver door lock switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 19 |
17 | Replace the passenger door lock switch. Refer to Power Door Lock Switch, Pull Handle, Map Pocket, Energy Absorber Replacement - Passenger Door . Did you complete the replacement? | Go to Step 20 | -- |
18 | Replace the appropriate door module. Refer to Control Module References in Computer/Integrating Systems for replacement, setup and programming. Did you complete the replacement? | Go to Step 20 | -- |
19 | Replace the driver door lock switch. Refer to Driver Door Latch Release, Power Window and Power Mirror Switch, and Bezel Replacement . Did you complete the replacement? | Go to Step 20 | -- |
20 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 2 |
