Tools Required

1. Remove the camshaft cover. Refer to Camshaft Cover Replacement .
2. Remove the exhaust camshaft position (CMP) sensor. Refer to Camshaft Position Sensor Replacement - Exhaust in Engine Controls-3.5L (L52).
3. Remove the Intake camshaft position (CMP) sensor. Refer to Camshaft Position Sensor Replacement - Intake in Engine Controls-3.5L (L52).



4. Rotate the crankshaft in the engine rotational direction clockwise, until the #1 piston is at top dead center (TDC) on the compression stroke.

The word Delphi on the exhaust camshaft position actuator will be parallel with the cylinder head to cam cover mating surface.

Caution: Refer to Camshaft Holding Tool Caution in the Preface section.




5. Install the J 44221 to the rear of the camshafts.
6. Remove the intake and the exhaust camshaft sprocket bolts.

Discard the bolts.




7. Install the J 44222 onto the cylinder head and adjust the horizontal bolts into the camshaft sprockets in order to maintain chain tension and keep from disturbing the timing chain components.
8. Carefully slide the sprockets with the timing chain from the camshafts to the J 44222 .



9. Alternately loosen the camshaft cap bolts a few turns at a time until all valve spring pressure has been released.

Important: Place the camshaft caps in a rack to ensure the caps are installed in the same location from which they were removed.

10. Remove the camshaft caps.
11. Remove the J 44221 from the camshafts.



12. Remove the camshafts from the cylinder head.
13. Clean and inspect the camshafts. Refer to Camshafts Cleaning and Inspection .

1. Coat the camshaft journals, camshaft journal thrust face, and camshaft lobes with clean engine oil.



2. Install the J 44221 with the camshaft flats up and the #1 piston at TDC.
3. Install the intake and exhaust camshafts to their original positions.



4. Observe the markings on the camshaft caps. Each camshaft cap is marked in order to identifiy its location. The markings have the following meanings:

•	The arrow should point to the front of the engine

•	The number indicates the position from the front of the engine

•	The "E" indicates the exhaust camshaft.

•	The "I" indicates the intake camshaft.

Notice: Refer to Fastener Notice in the Preface section.




5. Install the camshaft caps according to the identification marks.
6. Install the camshaft cap bolts. Tighten the bolts evenly in order to compress the valve springs before final torque.

Tighten
Tighten the camshaft cap bolts to 12 N·m (106 lb in).





Important: 

•	To aid in aligning the sprockets to the camshafts, use a 25 mm (1 in) wrench on the hex of the camshafts to rotate

•	Ensure the alignment pins are properly engaged with the camshafts

7. Carefully slide the sprockets with the timing chain from the J 44222 to the camshafts.
8. Remove the J 44222 from the cylinder head.
9. Install the new intake camshaft sprocket bolt.
10. Install the new exhaust camshaft actuator bolt.

Tighten

1. Tighten the intake camshaft sprocket bolt to 20 N·m (15 lb ft).
2. Use the J 45059 to rotate the intake camshaft sprocket bolt an additional 100 degrees.
3. Tighten the exhaust camshaft actuator bolt to 25 N·m (18 lb ft).
4. Use the J 45059 to rotate the exhaust camshaft actuator bolt an additional 135 degrees.



11. Remove the J 44221 from the camshafts.
12. Install the Intake camshaft position (CMP) sensor. Refer to Camshaft Position Sensor Replacement - Intake in Engine Controls-3.5L (L52).
13. Install the exhaust camshaft position (CMP) sensor. Refer to Camshaft Position Sensor Replacement - Exhaust in Engine Controls-3.5L (L52).
14. Install the camshaft cover. Refer to Camshaft Cover Replacement .