GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC B0595 01: Fasten Seatbelt Indicator Circuit Short to Battery

DTC B0595 06: Fasten Seatbelt Indicator Circuit Short to Ground or Open

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

Driver Seat Belt Sensor Signal

B0595 06, 1

B0595 06, 2

B0595 06, 2

B0595 01, 2

B0595 01, B0595 06

Driver Seat Belt Sensor Low Reference

--

B0595 06, 2

B0595 06, 2

2

B0595 01, B0595 06

1. Indicator will remain ON with seat belt buckled.

2. Indicator will illuminate only for the bulb test.

Circuit/System Description

The inflatable restraint sensing and diagnostic module (SDM) sends the status of the driver seat belt switch to the instrument panel cluster (IPC) via a GMLAN serial data message. If the seat belt is unfastened, the SDM will send a message to the IPC to illuminate the fasten safety belt indicator for 72 seconds or until the seat belt is fastened.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0595 01

The SDM detects the seat belt sensor circuit is shorted to voltage for 2 seconds.

B0595 06

The SDM detects the seat belt sensor circuit is shorted to ground or open for 2 seconds.

Action Taken When the DTC Sets

    • The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.
    • The SDM will store the DTC.

Conditions for Clearing the DTC

    • The condition for setting the DTC no longer exists.
    • A history DTC will clear once 100 fault-free ignition cycles have occurred.

Reference Information

Schematic Reference

    •  Seat Belt Schematics
    •  SIR Schematics

Connector End View Reference

Seat Belt Connector End Views

Description and Operation

Seat Belt System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions

Circuit/System Verification

Ignition ON, perform the IPC Display Test using the scan tool and verify the driver seat belt indicator is illuminated.

If the indicator does not illuminate, replace the IPC.

Circuit/System Testing

    Important: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector.

       • The BCM
       • The left seat belt switch
       • The SDM
       • The left seat belt switch harness connector
       • The SDM wiring harness connector

  1. Ignition OFF, disconnect the harness connector at the left seat belt switch.
  2. Ignition OFF, test for less than 1.0 ohm of resistance between the low reference circuit terminal C and ground.
  3. If greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the SDM.
  4. Ignition ON, verify the scan tool driver seat belt switch parameter is Unbuckled.
  5. If not the specified value, test the signal circuit terminal for a short to ground. If the circuit tests normal replace the SDM.
  6. Install a 3-amp fused jumper wire between the signal circuit terminal A and the low reference circuit terminal C. Verify the scan tool driver seat belt switch parameter is Buckled.
  7. If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the SDM.
  8. If all circuits test normal, replace the left seat belt switch.

Component Testing

  1. Ignition OFF, disconnect the harness connector at the left seat belt switch.
  2. Test for infinite resistance between the signal circuit terminal A and the low reference terminal C.
  3. If not the specified value, replace the left seat belt switch.
  4. With the seat belt buckled, test for less than 2 ohms of resistance between the signal circuit terminal A and the low reference terminal C.
  5. If greater than the specified range, replace the left seat belt switch.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Driver or Passenger Seat Belt Buckle Replacement
    •  Control Module References for SDM and IPC replacement, setup, and programming