GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The engine coolant temperature (ECT) sensor is a variable resistor, that measures the temperature of the engine coolant. The ECT sensor has a signal circuit and a low reference circuit. The engine control module (ECM) supplies 5 volts to the ECT signal circuit and a ground for the ECT low reference circuit. When the ECT is cold, the sensor resistance is high. When the ECT increases, the sensor resistance decreases. With high sensor resistance, the ECM detects a high voltage on the ECT signal circuit. With lower sensor resistance, the ECM detects a lower voltage on the ECT signal circuit. If the ECM detects an excessively high ECT signal voltage, which is a low temperature indication, DTC P1115 sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P1115 Engine Coolant Temperature (ECT) Sensor Circuit Intermittent High Voltage

Conditions for Running the DTC

    • The engine is running for more than one minute.
        OR
    • The engine run time is less than one minute when the intake air temperature (IAT) is more than -7°C (+19°F).
    • This DTC runs continuously within the enabling conditions.

Conditions for Setting the DTC

The ECM detects that the ECT sensor parameter is less than -39°C (-38°F) intermittently for more than 5 seconds.

Action Taken When the DTC Sets

    • The control module stores the DTC information into memory when the diagnostic runs and fails.
    • The malfunction indicator lamp (MIL) will not illuminate.
    • The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records.
    • The driver information center, if equipped, may display a message.

Conditions for Clearing the DTC

    • A current DTC Last Test Failed clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic.
    • Clear the DTC with a scan tool.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Controls Connector End Views or Engine Control Module Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

Important: The cooling fans will be commanded ON when certain engine coolant temperature (ECT) DTCs are set.

Observe the ECT sensor parameter with a scan tool.

Is the ECT sensor parameter less than the specified value?

-39°C (-38°F)

Go to Step 4

Go to Step 3

3

  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 90 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for running the DTC. You may also operate he vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 4

Go to Testing for Intermittent Conditions and Poor Connections

4

  1. Disconnect the ECT sensor.
  2. Measure the voltage from the signal circuit of the ECT sensor to a good ground with a DMM. Refer to Circuit Testing , Inducing Intermittent Fault Conditions , and Wiring Repairs .

Is the voltage more than the specified value?

5.2 V

Go to Step 5

Go to Step 6

5

Important: If a short to voltage occurs, the ECT sensor may be damaged.

Test the ECT signal circuit for an intermittent short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 15

Go to Step 12

6

  1. Connect a 3-amp fused jumper between the signal circuit of the ECT sensor and the low reference circuit. Refer to Using Fused Jumper Wires .
  2. Observe the ECT sensor parameter with the scan tool.

Is the ECT sensor parameter more than the specified value?

149°C (300°F)

Go to Step 10

Go to Step 7

7

  1. Connect a 3-amp fused jumper wire between the signal circuit of the ECT sensor and a good ground.
  2. Observe the ECT sensor parameter with a scan tool.

Is the ECT sensor parameter more than the specified value?

149°C (300°F)

Go to Step 9

Go to Step 8

8

Test the signal circuit of the ECT sensor for an intermittent high resistance or an open. Refer to Circuit Testing , Inducing Intermittent Fault Conditions , and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 15

Go to Step 12

9

Test the ECT sensor low reference circuit for an intermittent high resistance or an open. Refer to Circuit Testing , Inducing Intermittent Fault Conditions , and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 15

Go to Step 12

10

Test the ECT signal circuit for an intermittent short to any 5-volt reference circuit. Refer to Circuit Testing , Inducing Intermittent Fault Conditions , and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 15

Go to Step 11

11

Test for an intermittent and for a poor connection at the ECT sensor. Refer to Testing for Intermittent Conditions and Poor Connections , Inducing Intermittent Fault Conditions , and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 15

Go to Step 13

12

Test for an intermittent and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections , Inducing Intermittent Fault Conditions , and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 15

Go to Step 14

13

Replace the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement .

Did you complete the replacement?

--

Go to Step 15

--

14

Replace the ECM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 15

--

15

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 90 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 16

16

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK