GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2005 🢒 Classic 🢒 Restraints 🢒 SIR 🢒 Steering Wheel Inflatable Restraint Module Coil Replacement

Removal Procedure

    Caution: Refer to SIR Caution in the Preface section.


    Object Number: 294367 Size: SH
  1. Disable the SIR System. Refer to SIR Disabling and Enabling .
  2. Remove the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement .
  3. Remove the steering wheel nut.
  4. Note the mark on the steering shaft and the steering wheel to ensure proper alignment during installation.
  5. Remove the steering wheel from the steering shaft. Refer to Steering Wheel Replacement in Steering Wheel and Column.
  6. Remove the steering column trim covers. Refer to Steering Column Trim Covers Replacement in Steering Wheel and Column.

    7. Object Number: 322951 Size: SH
  7. Remove the wire harness straps from the steering wheel column wire harness.
  8. Remove the instrument panel carrier. Refer to Instrument Panel Carrier Replacement in Instrument Panel, Gages, and Console.
  9. Disconnect the SIR harness from the back of the fuse panel.
  10. Remove the retaining ring (3).
  11. Remove the SIR coil (4) from the steering shaft.
  12. If replacing, discard the SIR coil.

Installation Procedure

    Object Number: 332911 Size: SH
  1. To install the SIR coil, perform the following procedure:
    2. 1.1. Aim the wheels straight ahead.
    1.2. Align the block tooth and the centering mark on the race and upper shaft assembly at the 12 o'clock position.

    Object Number: 396373 Size: SH

    Important: The new SIR coil will be pre-centered. Do not remove the centering tab from the new SIR coil until the installation is complete. If the SIR coil does not come with a centering tab, you must center the SIR coil.

  2. If centering is required, refer to Inflatable Restraint Steering Wheel Module Coil Centering in Steering Wheel and Column.

    3. Object Number: 312359 Size: SH
  3. Align the SIR coil assembly (1) with the horn tower on the turn signal cancel cam assembly (2).

    4. Object Number: 322951 Size: SH

    Important: The new SIR coil will be pre-centered. Do not remove the centering tab from the new SIR coil until the installation is complete.

  4. Slide the new SIR coil (4) onto the steering shaft assembly (2).
  5. Firmly seat the retaining ring (3) into the groove on the steering shaft assembly (2).
  6. Remove and discard the centering tab from the new SIR coil (4).
  7. Connect the SIR harness to the back of the fuse panel.
  8. Install the instrument panel carrier. Refer to Instrument Panel Carrier Replacement in Instrument Panel, Gages, and Console.
  9. Install the steering column trim covers. Refer to Steering Column Trim Covers Replacement in Steering Wheel and Column.

    10. Object Number: 294367 Size: SH
  10. Feed the wiring through the steering wheel.
  11. Align the steering wheel with the mark on the steering shaft. Install the steering wheel onto the shaft.
  12. Install the nut for the steering wheel.

    13. Tighten
    Tighten the nut to 41 N·m (30 lb ft).

  13. Install the inflatable restraint steering wheel module. Refer to Inflatable Restraint Steering Wheel Module Replacement .
  14. Enable the SIR system. Refer to SIR Disabling and Enabling .