Heated Oxygen Sensor Replacement Bank 2

Notice: The Heated Oxygen Sensors each use a permanently attached pigtail and connector. This pigtail should not be removed from the heated oxygen sensor. Damage or removal of the pigtail or connector could affect proper operation of the heated oxygen sensor.

Important: Take care when handling the rear heated oxygen sensor (HO2S 2). The in-line connector and louvered end must be kept free of grease, dirt or other contaminants. Avoid using cleaning solvents of any type. DO NOT drop or roughly handle the HO2S 2.

1. Turn OFF the ignition.
2. Disconnect the HO2S 2 connector, in the engine compartment.
3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Notice: The use of excessive force may damage the threads in the exhaust manifold/pipe.

4. Carefully remove the HO2S 2.

Important: A special anti-seize compound is used on the HO2S 2 threads. The compound consists of a liquid graphite and glass beads. The graphite will burn away but the glass beads will remain, making the sensor easier to remove. New or service sensors already have the compound applied to the threads. If the sensor is removed and is to be reinstalled, the threads must be coated with an anti-seize compound before reinstallation.

1. Coat the threads only of the HO2S 2 with anti-seize compound, if necessary.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the HO2S 2.

Tighten
Tighten the HO2S 2 to 41 N·m (30 lb ft).

3. Lower the vehicle.
4. Reconnect the HO2S 2 connector, in the engine compartment.

Heated Oxygen Sensor Replacement Bank 1

Notice: The oxygen sensor uses a permanently attached pigtail and connector. Do not remove the pigtail from the oxygen sensor. Damage to or removal of the pigtail connector could affect proper operation of the oxygen sensor.

Notice: The use of excessive force may damage the threads in the exhaust manifold/pipe.

Important: The in-line connector and louvered end must be kept clear of grease, dirt or other contaminants. Avoid using cleaning solvents of any type. DO NOT drop or roughly handle the oxygen sensor.

Important: The oxygen sensor may be difficult to remove when the engine temperature is less than 48°C (120 °F).

1. Remove the exhaust manifold heat shield. Refer to Exhaust Manifold Replacement in Engine Exhaust.



2. Disconnect the oxygen sensor harness connector.
3. Remove the oxygen sensor.

Important: A special anti-seize compound is used on the oxygen sensor threads. The compound consists of a liquid graphite and glass beads. The graphite will burn away, but the glass beads will remain, making the sensor easier to remove. New or service sensors will have the compound applied to the threads. If a sensor is removed and is to be reinstalled, the threads must have an anti-seize compound applied before installation.

1. Coat the threads of the oxygen sensor with anti-seize compound, if necessary.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the oxygen sensor.

Tighten
Tighten the oxygen sensor to 30 N·m (22 lb ft).

3. Connect the oxygen sensor harness connector.



4. Install the exhaust manifold heat shield. Refer to Exhaust Manifold Replacement in Engine Exhaust.