DTC P1810 Pressure Switch Assembly Malfunction 5.7L and 7.4L Gas
Circuit Description
the TFP Val. Position Sw. consists of five normally-open pressure switches. The VCM supplies battery voltage to each range signal. By grounding one or more of these circuits through various combinations of the pressure switches, the VCM detects what manual valve position has been selected and compares the actual voltage combination of the switches to a TFP Val. Position Sw. combination chart stored in memory.
the TFP Val. Position Sw. assembly cannot distinguish between Park and Neutral because the monitored valve body pressures are identical in both cases. With the ignition On and the engine Off, D2 is indicated. When the transmission 20-way connector is disconnected, the ground potential for the three range signals to the VCM is removed, and with the ignition On, D2 is indicated.
When the VCM detects an invalid state of the TFP Val. Position Sw. circuit by deciphering the TFP Val . Position Sw. inputs, then DTC P1810 sets. DTC P1810 is a type D DTC. For California emissions vehicles DTC P1810 is a type B DTC.
Conditions for Setting the DTC
DTC P1810 sets if any of the following Conditions occur:
Condition 1:
- No system voltage DTC P0560.
- The engine is running and is not in fuel cut off.
- The VCM detects an illegal TFP Val. Position Sw. combination for greater than 5 seconds.
Condition 2:
| • | No system voltage DTC P0560. |
| • | No VSS DTC P0502. |
| • | The engine speed is less than 240 RPM for 0.3 seconds, 240-800 RPM for greater than 0.1 seconds and then greater than 800 RPM and the vehicle speed is less than 3 km/h (2 mph). |
| • | The VCM detects the gear range as D2 before and after start up. |
| • | The condition exists for greater than 8 seconds. The VCM looks for a condition change only at start-up. |
Condition 3:
| • | No TP Sensor DTCs P0121, P0122, or P0123. |
| • | No ISS Sensor DTCs P0716 or P0717. |
| • | No VSS DTC P0502. |
| • | No 1-2 SS Valve DTCs P0751 or P0753. |
| • | No 2-3 SS Valve DTCs P0756 or P0758. |
| • | The vehicle speed is greater than 8 km/h (5 mph). |
| • | The TP Sensor is greater than 12%. |
| • | The engine torque is greater than 80 lb ft. |
| • | The engine is running for more than 5 seconds. |
| • | The TFP Val. Position Sw. indicates the following: |
| - | P/N when the ratio indicates less than 1.58:1 for greater than 15 seconds. |
| - | Reverse when the ratio indicates D4, D3, D2, and D1 for greater than 7 seconds. |
| - | D4, D3, D2, and D1 when the ratio indicates reverse for greater than 7 seconds. |
Action Taken When the DTC Sets
| • | The VCM commands maximum line pressure. |
| • | The VCM assumes D4 for the PRNDL shift pattern. |
| • | The VCM freezes shift adapts. |
| • | The VCM forces the TCC on in fourth gear. |
| • | The VCM illuminates the Malfunction Indicator Lamp for California Emission Vehicles. |
Conditions for Clearing the DTC
- For California emissions vehicles, the VCM turns OFF the MIL after three consecutive ignition cycles without a failure reported.
- A scan tool can clear the DTC from the VCM history. The VCM clears the DTC from the VCM history if the vehicle completes 40 warm-up cycles without a failure reported.
- The VCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the VCM.
Diagnostic Aids
| • | Refer to the accompanying chart for the normal range signals and the illegal combinations. |
| • | Inspect the wiring for poor electrical connections at the VCM. Inspect the wiring for poor electrical connections at the transmission 20-way connector. Look for the following conditions: |
| - | A bent terminal |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Poor terminal tension |
| - | A chafed wire |
| - | A broken wire inside the insulation |
| • | When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. |
| • | DTC P1810 can be falsely set during a fluid fill procedure. After refilling the fluid, cycle key down then start and run the vehicle for 20 seconds. Key down and allow the VCM to power down, and then restart the vehicle. |
| • | DTC P1810 can be set falsely by low pump pressure or a stuck pressure regulator. |
| • | DTC P1810 can be set by a slipping forward clutch assembly. It may allow the VCM to see a 2.08:1 ratio (reverse) when the manual valve position is indicated as D4. |
| • | First diagnose and clear any engine DTCs or TP Sensor codes that are present. Then inspect for any transmission DTCs that may have reset. |
| • | Refer to the Range Signal table. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the indicated range signal to the manual valve that is actually selected.
-
This step tests the voltage from the VCM to the transmission 20-way connector.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||||||||||
2 |
Did you perform the inspections? | -- | -- | |||||||||
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. Does each selected transmission range match the scan tool TFP Switch display? | -- | Go to Diagnostic Aids | ||||||||||
Is B+ displayed on all three circuits? | -- | |||||||||||
5 | Inspect the circuits that did not indicate B+ in Step 4, for an open or short to ground condition. Refer to Electrical Diagnosis, Section 8. Did you find a problem? | -- | ||||||||||
6 | To verify that circuits 1224, 1225, and 1226 are not shorted together, use a fused jumper to ground on each circuit while monitoring the scan tool TFP Switch display. When a range signal circuit is grounded, are the other range signal circuits affected? | -- | ||||||||||
7 | Inspect the VCM connector terminals for poor connections. If you find no problem, replace the VCM. Refer to VCM Replacement/Programming , Section 6. Is the replacement complete? | -- | -- | |||||||||
8 | Repair the affected wiring as needed. Refer to Electrical Diagnosis, Section 8. Is the repair complete? | -- | -- | |||||||||
9 | Replace the TFP Val. Position Sw. Refer to Automatic Transmission Fluid Pressure Manual Valve Position Switch Replacement, in On-Vehicle Service. Is the replacement complete? | -- | -- | |||||||||
10 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
DTC P1810 Pressure Switch Assembly Malfunction 6.5L Diesel
Circuit Description
The TFP Val. Position Sw. consists of five normally-open pressure switches. The PCM supplies battery voltage to each range signal. By grounding one or more of these circuits through various combinations of the pressure switches, the PCM detects what manual valve position has been selected and compares the actual voltage combination of the switches to a TFP Val. Position Sw. combination chart stored in memory.
The TFP Val. Position Sw. cannot distinguish between Park and Neutral because the monitored valve body pressures are identical in both cases. With the ignition On and the engine Off, D4 is indicated. When the transmission 20-way connector is disconnected, the ground potential for the three range signals to the PCM is removed, and with the ignition On, D2 is indicated.
When the PCM detects an invalid state of the TFP Val. Position Sw. circuit by deciphering the TFP Val . Position Sw. inputs, then DTC P1810 sets. DTC P1810 is a type A DTC.
Conditions for Setting the DTC
DTC P1810 sets if any of the following conditions occur:
Condition 1:
| • | No system voltage DTC P0560. |
| • | The engine is running. |
| • | The PCM detects an illegal TFP Val. Position Sw. combination for greater than 25 seconds. |
Condition 2:
| • | No system voltage DTC P0560. |
| • | No OSS Sensor DTCs P0722 or P0723. |
| • | The engine speed is less than 50 RPM for 0.5 seconds, 50-525 RPM for greater than 0.1 seconds and then the engine speed is greater than 525 RPM and the vehicle speed is less than 3 km/h (2 mph). |
| • | The PCM detects the gear range as D2 before and after start up. |
| • | The condition exists for greater than 7 seconds. The PCM looks for a condition change only at start-up. |
Condition 3:
| • | No APP Sensor DTCs P0121, P0122, P0123, P0220, P0221, P0222, P0223, P0225, P0226, P0227, or P0228. |
| • | No ISS Sensor DTCs P0716 or P0717. |
| • | No OSS DTCs P0722 or P0723. |
| • | No 1-2 SS Valve DTCs P0751 or P0753. |
| • | No 2-3 SS Valve DTCs P0756 or P0758. |
| • | The engine speed is less than 3750 RPM. |
| • | The vehicle speed is greater than 8 km/h (5 mph). |
| • | The TP Sensor is greater than 12%. |
| • | The engine torque is 80-450 lb ft. |
| • | The engine is running for more than 5 seconds. |
| • | The TFP Val. Position Sw. indicates the following: |
| - | P/N when the ratio indicates less than 1.58:1 for greater than 10 seconds. |
| - | Reverse when the ratio indicates D4, D3, D2, and D1 for greater than 15 seconds. |
| - | D4, D3, D2, and D1 when the ratio indicates reverse for greater than 15 seconds. |
Action Taken When the DTC Sets
| • | The PCM commands maximum line pressure. |
| • | The PCM assumes D4 for the PRNDL shift pattern. |
| • | The PCM freezes shift adapts. |
| • | The PCM illuminates the Malfunction Indicator Lamp (MIL). |
Conditions for Clearing the DTC
- The PCM turns OFF the MIL after three consecutive ignition cycles without a failure reported.
- A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported.
- The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM
Diagnostic Aids
| • | Refer to the accompanying chart for the normal range signals and the illegal combinations. |
| • | Inspect the wiring for poor electrical connections at the PCM Inspect the wiring for poor electrical connections at the transmission 20-way connector. Look for the following conditions: |
| - | A bent terminal |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Poor terminal tension |
| - | A chafed wire |
| - | A broken wire inside the insulation |
| • | When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. |
| • | DTC P1810 can be falsely set during a fluid fill procedure. After refilling the fluid, cycle key down then start and run the vehicle for 20 seconds. Key down and allow the PCM to power down, and then restart the vehicle. |
| • | DTC P1810 can be set falsely by low pump pressure or a stuck pressure regulator. |
| • | DTC P1810 can be set by a lipping forward clutch assembly. It may allow the PCM to see a 2.08:1 ratio (reverse) when the manual valve position is indicated as D4. |
| • | First diagnose and clear any engine DTCs or APP Sensor codes that are present. Then inspect for any transmission DTCs that may have reset. |
| • | Refer to the Range Signal table. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the indicated range signal to the manual valve that is actually selected.
-
This step tests the voltage from the PCM to the transmission 20-way connector.
Step | Action | Value(s) | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||||||||||
2 |
Did you perform the inspections? | -- | -- | |||||||||
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data. Does each selected transmission range match the scan tool Trans Range display? | -- | Go to Diagnostic Aids | ||||||||||
Do all three circuits display B+? | -- | |||||||||||
5 | For the circuits that did not indicate B+ in Step 4, inspect for an open or short to ground condition. Refer to Electrical Diagnosis, Section 8. Did you find a problem? | -- | ||||||||||
6 | To verify that circuits 1224, 1225, and 1226 are not shorted together, use a fused jumper to ground on each circuit while monitoring the scan tool Trans Range display. When a range signal circuit is grounded, are the other range signal circuits affected? | -- | ||||||||||
7 | Inspect the PCM connector terminals for poor connections. If you find no problem, replace the PCM. Refer to Powertrain Control Module Replacement/Programming , Section 6. Is the replacement complete? | -- | -- | |||||||||
8 | Repair the affected wiring as needed. Refer to Electrical Diagnosis, Section 8. Is the repair complete? | -- | -- | |||||||||
9 | Replace the TFP Val. Position Sw. Refer to Automatic Transmission Fluid Pressure Manual Valve Position Switch Replacement, in On-Vehicle Service. Is the replacement complete? | -- | -- | |||||||||
10 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
