GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC B2580 00: Headlamp High Beam Control Circuit

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Headlamp LO/HID Relay B+

1

1

--

--

High Beam Relay B+

2

2

--

--

Headlamp Flash to Pass Signal

4

4

4

--

Headlamp Dimmer Switch Signal

4

4

4

--

Headlamp Low Beam Control

1

1

1

--

Headlamp Low Beam Relay Control

1

1

B2575 00

--

Headlamp Switch Off Control

B257A 00

3

3

--

Headlamp Switch On Control

B257A 00

3

3

--

Headlamp High Beam Control

2

2

2

--

Headlamp High Beam Relay Control

2

2

B2580 00

--

Park Lamp Switch On Control

B257A 00

B257A 00

3

--

Headlamp Switch Ground

--

2

--

--

Turn Signal/Multifunction Switch Malfunction

--

4

--

--

  1. Headlamp Malfunction - Low Beam
  2. Headlamp Malfunction - High Beam
  3. Headlamp Switch Malfunction
  4. Turn Signal/Multifunction Switch Malfunction

Circuit/System Description

When the turn signal/multifunction switch is placed in the headlamps high or flash to pass (FTP) position, ground is applied to the body control module (BCM) through the headlamp high beam signal circuit or the flash to pass signal circuit. The BCM applies ground to the headlamp HIGH BEAM relay control circuit which energizes the HIGH BEAM relay. With the HIGH BEAM relay energized, the switch contacts close allowing B+ to flow through the HI BEAM fuses to the high beam headlamps. Ground for the left headlamp is supplied at G100 and the right headlamp receives ground at G101.

Conditions for Running the DTC

    • Battery voltage must be between 9-16 volts.
    • Headlamps ON.

Conditions for Setting the DTC

DTC B2580 00 will set when the BCM detects a short to voltage in the headlamp HIGH BEAM relay control circuit.

Actions Taken When the DTC Sets

When DTC B2580 00 is present, the high beam headlamps and flash to pass (FTP) will not operate.

Conditions for Clearing the DTC

    • The condition responsible for setting the DTC no longer exists.
    • A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

Headlights/Daytime Running Lights (DRL) Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Exterior Lighting Systems Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Testing

  1. Ignition OFF, disconnect the X4 harness connector at the underhood fuse block.
  2. Connect a test lamp between the control circuit terminal C3 and B+.
  3. Command the High Beam Relay Command ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
  4. If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.
    If the test lamp is always OFF, test the control circuit for a short to voltage or open/high resistance. If the circuit tests normal, replace the BCM.
  5. If all circuits test normal, test or replace the underhood fuse block.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Underhood Electrical Center or Junction Block Replacement
    •  Control Module References for BCM replacement, setup, and programming