Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B2600 00: Daytime Running Lamp Control CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Daytime Running Lamp Relay B+ | 1 | 1 | -- | -- |
Headlamp LO/HID Relay B+ | 1 | 1 | -- | -- |
High Beam Relay B+ | 1 | 1 | -- | -- |
Ambient Light Sensor Signal Circuit | B2645 03 | B2645 07 | B2645 07 | -- |
Headlamp Flash to Pass Signal | 4 | 4 | 4 | -- |
Headlamp Dimmer Switch Signal | 4 | 4 | 4 | -- |
Daytime Running Lamp Relay Control | 3 | 3 | B2600 00 | -- |
Headlamp Low Beam Control | 1 | 1 | 1 | -- |
Headlamp Low Beam Relay Control | 1 | 1 | B2575 00 | -- |
Headlamp Switch Off Control | B257A 00 | 2 | 2 | -- |
Headlamp Switch On Control | B257A 00 | 1 | 1 | -- |
Headlamp High Beam Control | 1 | 1 | 1 | -- |
Headlamp High Beam Relay Control | 1 | 1 | B2580 00 | -- |
Park Lamp Switch On Control | B257A 00 | B257A 00 | 2 | -- |
Ambient Light Sensor Ground Circuit | -- | B2645 07 | -- | -- |
Headlamp Switch Ground | -- | 2 | -- | -- |
Turn Signal/Multifunction Switch Malfunction | -- | 4 | -- | -- |
| ||||
Circuit/System Description
The ambient light sensor is used to monitor outside lighting conditions. The ambient light sensor provides a voltage signal that will vary between 0.2 and 4.9 volts depending on outside lighting conditions. The body control module (BCM) provides a 5-volt reference signal to the ambient light sensor. The body control module (BCM) monitors the ambient light sensor signal circuit to determine if outside lighting conditions are correct for either daytime running lights (DRL) or automatic lamp control (ALC) when the headlamp switch is in the AUTO position. In daylight conditions, the BCM will command the DRLs ON by applying ground to the DRL relay via the DRL relay control circuit. When the BCM applies ground to the DRL relay control circuit, the DRL relay coil energizes causing the relay switch contacts to close. With the DRL relay energized, voltage is applied through the relay switch contacts, the DRL Resistor , and the DRL fuse to the left and right low beam headlamp fuses illuminating the low beam headlamps. Any function or condition that turns the headlamps ON will cancel DRL operation. Any function or condition that turns on the headlamps will cancel DRL operation.
Conditions for Running the DTC
| • | Battery voltage must be between 9-16 volts. |
| • | Headlamp switch in AUTO position. |
Conditions for Setting the DTC
DTC B2600 00 will set when the BCM detects a short to voltage in the DRL relay control circuit.
Action Taken When the DTC Sets
The BCM will disable the DRL relay control circuit.
Conditions for Clearing the DTC
| • | The condition responsible for setting the DTC no longer exists. |
| • | A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition OFF, disconnect the X4 harness connector at the underhood fuse block.
- Connect a test lamp between the control circuit terminal H4 and B+.
- Command the DRL ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, test or replace the underhood fuse block.
| ⇒ | If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, setup, and programming |
