GM Service Manual Online
For 1990-2009 cars only

Danger: This procedure should not be performed on high voltage circuits. Performing this procedure on high voltage circuits may result in serious injury or death.

Important: Always be sure to reinstall the connector position assurance (CPA) and terminal position assurance (TPA) when reconnecting connectors or replacing terminals.

Front probe

Disconnect the connector and probe the terminals from the mating side (front) of the connector.

Notice: Do not insert test equipment probes (DVOM etc.) into any connector or fuse block terminal. The diameter of the test probes will deform most terminals. A deformed terminal will cause a poor connection, which will result in a system failure. Always use the J-35616 GM-Approved Terminal Test Kit in order to front probe terminals. Do not use paper clips or other substitutes to probe terminals.

When using the J-35616 GM-Approved Terminal Test Kit, ensure the terminal test adapter choice is the correct size for the connector terminal. Do not visually choose the terminal test adapter because some connector terminal cavities may appear larger than the actual terminal in the cavity. Using a larger terminal test adapter will damage the terminal. Refer to the J-35616 GM-Approved Terminal Test Kit label on the inside of the J-35616 GM-Approved Terminal Test Kit for the correct adapter along with the connector end view for terminal size.

Important: When probing female 0.64 terminals, it is important to use the correct adapter. There have been some revisions to the test adapter for 0.64 terminals. The proper adapter for 0.64 terminals is the J 35616-64B which has a gold terminal and a black wire between the base and tip. Failure to use the proper test adapter may result in damage to the terminal being tested and improper diagnosis.

Refer to the following table as a guide in selecting the correct test adapter for front probing connectors:

Test Adapter

Description

J-35616-2A

150 Male Probe Adapter (gray)

J-35616-3

150 Female Probe Adapter (gray)

J-35616-4A

280 Male Probe Adapter (purple)

J-35616-5

280 Female Probe Adapter (purple)

J-35616-6

100W Male (round) Probe Adapter (brown)

J-35616-7

100W Female (round) Probe Adapter (brown)

J-35616-8

Weather Pack Male Probe Adapter (orange)

J-35616-9

Weather Pack Female Probe Adapter (orange)

J-35616-10

100W Male (round) Probe Adapter (green)

J-35616-11

100W Female (round) Probe Adapter (green)

J-35616-12

130 Male Probe Adapter (blue)

J-35616-13

130 Female Probe Adapter (blue)

J-35616-14

150 Male Probe Adapter (green)

J-35616-16

100 Male Probe Adapter (lt green)

J-35616-17

100 Female Probe Adapter (lt green)

J-35616-18

220 Male Probe Adapter (black)

J-35616-19

220 Female Probe Adapter (black)

J-35616-21

950 Female Probe Adapter (red)

J-35616-22

950 Male Probe Adapter (red)

J-35616-31

500 Male Probe Adapter (orange)

J-35616-32

500 Female Probe Adapter (orange)

J-35616-33

160/180 Male Probe Adapter (yellow)

J-35616-34

160/180 Female Probe Adapter (yellow)

J-35616-35

280 Male Probe Adapter (violet)

J-35616-40

480 Male Probe Adapter (dk blue)

J-35616-41

480 Female Probe Adapter (dk blue)

J-35616-42

630 Male Probe Adapter (red)

J-35616-43

630 Female Probe Adapter (red)

J-35616-44

800 Male Probe Adapter (yellow)

J-35616-45

800 Female Probe Adapter (yellow)

J-35616-54

280 Male (round) Probe Adapter (tan)

J-35616-55

280 Female (round) Probe Adapter (tan)

J-35616-64B

0.64 Male Probe Adapter (lt blue)

J-35616-65B

0.64 Female Probe Adapter (lt blue)

J-35616-66

150 Male (round) Probe Adapter (yellow)

J-35616-67

150 Female (round) Probe Adapter (yellow)

Backprobe

Important: 

   • Backprobe connector terminals only when specifically required in diagnostic procedures.
   • Do not backprobe a sealed (Weather Pack®) connector, less than a 280 series Metri-Pack connector, a Micro-Pack connector, or a flat wire (dock and lock) connector.
   • Backprobing can be a source of damage to connector terminals. Use care in order to avoid deforming the terminal, either by forcing the test probe too far into the cavity or by using too large of a test probe.
   • After backprobing any connector, inspect for terminal damage. If terminal damage is suspected, test for proper terminal contact.

Do not disconnect the connector and probe the terminals from the harness side (back) of the connector.