GM Service Manual Online
For 1990-2009 cars only

Diagnostic Aids

If the drive belt(s) repeatedly falls off the accessory drive pulley(s), this may be caused by a pulley misalignment.

An extra load that is quickly applied or released by an accessory drive component may cause the drive belt(s) to fall off. Verify that the accessory drive component(s) are operating properly.

If the drive belt(s) is the incorrect length, the drive belt tensioner(s) may not maintain the proper tension on the drive belt(s).

Test Description

The number(s) below refer to the step(s) in the diagnostic table.

  1. This inspection is to verify the condition of the drive belt(s). Damage may have occurred to the drive belt(s) when the drive belt(s) fell off the pulleys. Inspect the drive belt(s) for cuts, tears, sections of ribs missing, or damaged belt plys.

  2. Misalignment of the accessory drive pulley(s) may be caused from improper mounting or incorrect installation of a accessory drive component, or the pulley may be bent inward or outward from a previous repair. Test for a misaligned pulley using a straight edge in the pulley grooves across two or three pulleys. If a misaligned pulley is found, refer to that accessory drive component for the proper removal and installation procedure of that pulley.

  3. Inspection of the accessory drive pulley(s) should include inspecting for bends, dents, or other damage that would prevent the drive belt from seating properly in the pulley grooves or on the smooth surface of a pulley when the back side of the belt(s) is used to drive the pulley.

  4. Accessory drive component brackets that are bent or cracked will also cause the drive belt(s) to fall off.

  5. Inspection of the fasteners can eliminate the possibility that a incorrect bolt, nut, spacer, or washer was installed. Missing, loose, or incorrect fasteners may cause pulley misalignment from the accessory drive bracket(s) moving under load. Over tightening the fasteners may cause misalignment of the accessory component bracket(s).

Step

Action

Yes

No

Notice: Refer to Belt Dressing Notice in the Preface section.

DEFINITION: The drive belt(s) falls off the pulleys or may not ride correctly on the pulleys.

1

Did you review the Symptoms - Engine Mechanical diagnostic information and perform the necessary inspections?

Go to Step 2

Go to Symptoms - Engine Mechanical

2

Inspect for a damaged drive belt(s).

Was a damaged drive belt(s) found?

Go to Step 3

Go to Step 4

3

Install a new drive belt(s). Refer to Drive Belt Replacement - Accessory or Air Conditioning Compressor Belt Replacement .

Does the drive belt(s) continue to fall off?

Go to Step 4

System OK

4

Inspect for a misaligned accessory drive pulley(s).

Did you find and correct the condition?

Go to Step 12

Go to Step 5

5

Inspect for a bent or dented accessory drive pulley(s).

Did you find and correct the condition?

Go to Step 12

Go to Step 6

6

Inspect for a bent or a cracked accessory drive bracket(s).

Did you find and correct the condition?

Go to Step 12

Go to Step 7

7

Inspect for incorrect, loose and/or missing fasteners.

Were there any incorrect, loose and/or missing fasteners?

Go to Step 8

Go to Step 9

8

Replace and incorrect and/or missing fasteners.

Tighten any loose fasteners. Refer to Fastener Tightening Specifications .

Does the drive belt continue to fall off?

Go to Step 9

System OK

9

Test the drive belt tensioner for correct operation. Refer to Drive Belt Tensioner Diagnosis .

Does the drive belt tensioner operate correctly?

Go to Step 11

Go to Step 10

10

Replace the drive belt tensioner. Refer to Drive Belt Tensioner Replacement - Accessory or Drive Belt Tensioner Replacement - Air Conditioning .

Does the drive belt continue to fall off?

Go to Step 11

System OK

11

Inspect for a failed drive belt idler(s) and/or tensioner pulley(s) bearing.

Did you find and repair the condition?

Go to Step 12

--

12

Run the engine in order to verify the repair.

Does the drive belt still fall off?

--

System OK