DTC P0724 Brake Switch Circuit High Input Gas LQ4
Circuit Description
The TCC/Stoplamp switch indicates the brake pedal status. The normally closed brake switch supplies a B+ signal on circuit 420 to the powertrain control module (PCM). The signal voltage circuit opens when the brakes are applied.
If the PCM detects a closed TCC/Stoplamp switch during decelerations, then DTC P0724 sets. DTC P0724 is a type C DTC.
Conditions for Running the DTC
| • | No OSS DTC P0502. |
| • | The following sequence of events occurs 10 consecutive times: |
| 1. | The vehicle speed is greater than 40 km/h (25 mph) for 7 seconds. |
| 2. | Then the vehicle speed is 8-40 km/h (5-25 mph) for 3.2 seconds. |
| 3. | Then the vehicle speed is less than 8 km/h (5 mph). |
Conditions for Setting the DTC
| • | All conditions are met for 10 occurrences. |
| • | The PCM detects a closed TCC/Stoplamp switch circuit (12 volts) during decelerations. |
Action Taken When the DTC Sets
| • | The PCM does not illuminate the malfunction indicator lamp (MIL). |
| • | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Failure Records. |
| • | The PCM stores DTC P0724 in PCM history. |
Conditions for Clearing the DTC
| • | A scan tool clears the DTC from PCM history. |
| • | The PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission-related diagnostic fault occurring. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | First diagnose and clear any engine DTCs or TP sensor codes that are present. Then inspect for any transmission DTCs that may have reset. |
| • | Inspect the connectors at the PCM, the TCC Stoplamp switch and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Wiring Systems. |
| • | Ask about the customer's driving habits and any unusual driving conditions he or she might have, such as stop and go traffic or expressway driving. |
| • | Inspect the brake switch for proper mounting and adjustment. |
| • | Inspect for the most current calibration ID and the latest bulletins. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | ||
2 |
Important: Before clearing the DTCs, use the scan tool in order to record the Failure Records. Using the Clear Info function erases the Failure Records from the PCM. Did the TCC/Brake Switch status change from CLOSED to OPEN? | -- | ||
Did the TCC/Stoplamp switch status change from CLOSED to OPEN? | -- | |||
4 | Replace the stoplamp switch. Refer to Stop Lamp Switch Replacement in Hydraulic Brakes. Did you complete the replacement? | -- | -- | |
5 |
Important: The condition that affects this circuit may exist in other connecting branches of the circuit. Refer to Power Distribution Schematics in Wiring Systems for complete circuit distribution. Test the input circuit (CKT 420) for a short to voltage. Was a short to voltage condition found? | -- | ||
6 | Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls. Did you complete the replacement? | -- | -- | |
7 | Perform the following procedure in order to verify the repair:
Does the Scan Tool TCC/Stoplamp switch status change from CLOSED to OPEN? | -- | System OK |
