LEAK-SERVICE AND PARTS INFORMATION
TRANSMISSION APPLICATIONS: SUBJECT: ------------------------- ------- 1968-88 HM-117 MANUAL TRANS. 1968-1988 LEAK-SERVICE AND PARTS (RPO M20) INFORMATION ON NEW STYRENE RUBBER 1968-88 CH/SM 465 MANUAL COATED FIBER GASKETS W/MANUAL TRANSMISSION (RPO MC8) TRANSMISSION
TRANSMISSION MODELS: VEHICLE APPLICATIONS: ------------------- -------------------- ALL C/K, R/V, P ALL MODEL YEARS
BULLETIN COVERS:
SUBJECT: ------- Leak Service And Parts Information On New Styrene Rubber Coated Fiber Gaskets
HM-117 TRANSMISSION MODELS:
All Models
HM-117 VEHICLE APPLICATIONS:
1968-88 C1, C2, C3 Trucks 1968-88 K1, K2, K3 Trucks 1968-88 R1, R2, R3 Trucks 1968-88 V1, V2 ,V3 Trucks
CH/SM-465 TRANSMISSION MODELS: ------------------------------ All Models
CH/SM 465 VEHICLE APPLICATIONS: ------------------------------- 1968-88 P4, P6 - Forward Control Motorhome Chassis 1968-88 B6 - Bus Chassis 1968-88 C5, C6, C7 - Medium Duty Trucks
BULLETIN COVERS: (Figure 1) ---------------- Service information on vehicles equipped with a HM-117 or CH/SM 465 manual transmission that may have fluid leaks. These fluid leaks should be serviced with new styrene rubber coated cellulose fiber gaskets, insuring flatness of the case mating surfaces and the addition of sealant to specified parts. The new gaskets are for the (top) cover (6), power take off (PTO) covers (58), main drive gear retainer (53), countershaft front bearing cap (75) and a universal 2WD and 4WD rear bearing retainer gasket (77 and 88).
DATE OF PRODUCTION CHANGE: (Figure 2) -------------------------- All units built after February 15, 1988 will have the new gaskets described above.
The jack screw holes in the cover were eliminated for the R/V and P Truck applications on February 4, 1988 and the C/K Truck applications on April 15, 1988.
SERVICE ACTION:
Inspect the case (59) mating surfaces for flatness using a metal straight edge and feeler gauge. If a 0.13mm (0.005 in.) feeler gauge can be put under the straight edge at any point, replace the case.
On models built before July 6, 1987 with a dowel pin hole that goes through the inside of the case, put RTV silicone specified in Service Parts Information around the edge of the dowel pin (7) that is on the cover (2) to prevent leakage (Figure 3).
For all models, install the new gaskets and put pipe sealant with teflon (TM) or equivalent on all the bolts. Put pipe sealant with teflon (TM) or equivalent on the drain and fill plugs (76), then torque all bolts and plugs to the specifications listed in Figure 1. The countershaft front bearing cap bolt (73) torque specification has been increased to 4 N m (3 ft. lb.) to prevent leakage.
SERVICE PARTS INFORMATION:
P/N 8672945 New Service Parts Gasket and Seal Package Contents:
Quantity Part Description -------- ---------------- 1 Gasket, Rear Bearing Retainer (2WD and 4WD) 1 Gasket, Main Drive Gear Bearing Retainer 1 Gasket, Countershaft Front Bearing Cap 2 Gasket, Power Take Off Cover 1 Gasket, Cover 1 Seal, Main Drive Gear Bearing Oil 1 Seal, U-Joint Front Flange Oil
Listed below are sealants referred to in this bulletin:
Quantity Part No. Part Description -------- -------- ---------------- 1 992545 Pipe Sealant with Teflon (TM) (50 ml - 1.69 oz.) 1 1052917 RTV Silicone GMS Type B (89 ml - 3 oz.)
SERVICE MANUAL REFERENCE:
Refer to the unit repair section of the appropriate service manual for the procedures.
Please record this information in any 1988 or earlier model year service manual. 1989 and future service manuals will include these revisions.
SERVICE NOTES:
Refill the transmission with only SAE 80W-90 gear lubricant. Do not use automatic transmission fluid or engine oil. This may cause foaming out the vent and durability concerns.
IMPORTANT: Some 1988 C/K Trucks equipped with a HM-117 may leak out the vent. To correct this condition, refer to the bulletins listed below outlining the procedure to add a remote vent system.
GMC Truck Bulletin 88-T-44 Chevrolet Bulletin 88-44-7B GM Canada Bulletin 887040-100 Hydra-matic Bulletin HM 87-86
On models equipped with the remote vent system, do not use a SAE 80W or SAE 80W-90 gear lubricant that has a hypoid additive (a GL5 rating on the label). This may cause a gear oil smell inside of the vehicle.
General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.
