DTC P0567 4.8L, 5.3L, 6.0L, and 8.1L
Circuit Description
The cruise control Resume/Accel switch is an input to the throttle actuator control (TAC) module. The TAC module uses the cruise control resume/accel switch signal circuit in order to detect when the driver has requested to accelerate the set vehicle speed or to resume the cruise control system. The TAC module detects a voltage signal on the cruise control resume/accel switch signal circuit when the switch is applied. The TAC module sends a serial data signal to the powertrain control module (PCM) via the UART serial data circuit. This DTC sets if the PCM receives a serial data signal from the TAC module indicating that voltage is present on the cruise control resume/accel switch signal circuit for longer than 90 seconds.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0567 Cruise Control Resume Switch Circuit
Conditions for Running the DTC
| • | The ignition is ON. |
| • | The cruise control switch is ON. |
Conditions for Setting the DTC
The PCM receives a serial data signal from the TAC module indicating that the Resume/Accel switch is applied for longer than 90 seconds.
Action Taken When the DTC Sets
| • | The PCM stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The PCM records the operating conditions at the time the diagnostic fails. The PCM stores this information in the Failure Records. |
| • | The Cruise Control System is disabled. |
Conditions for Clearing the DTC
| • | A last test failed, or the current DTC, clears when the diagnostic runs and does not fail. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if failures are not reported by this or any other emission related diagnostic. |
| • | Use a scan tool in order to clear the DTC. |
Diagnostic Aids
| • | Ensure that the Resume/Accel switch is not stuck or sticking in the engaged position. |
| • | For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Cruise Control Schematics Connector End View Reference: Master Electrical Component List | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
Does the Cruise Resume/Accel. Switch parameter display On? | Go to Step 3 | Go to Diagnostic Aids | |
3 |
Does the Cruise Resume/Accel. Switch parameter display On? | Go to Step 4 | Go to Step 5 |
4 | Test the cruise control resume/accel switch signal circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 6 |
5 | Inspect for poor connections at C4 of the multifunction switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 8 |
6 | Inspect for poor connections at the harness connector of the throttle actuator control (TAC) module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 7 |
7 | Replace the TAC module. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 9 | -- |
8 | Replace the multifunction switch. Refer to Turn Signal Multifunction Switch Replacement . Did you complete the replacement? | Go to Step 9 | -- |
9 |
Does the DTC reset? | Go to Step 2 | System OK |
DTC P0567 6.6L
Circuit Description
The cruise control resume/accel switch is an input to the engine control module (ECM). The ECM monitors the cruise control resume/accel switch signal circuit in order to detect when the driver has requested to accelerate the set vehicle speed or to resume the cruise control system. The ECM module detects a voltage signal on the cruise control resume/accel switch signal circuit when the switch is applied. This DTC sets if the ECM detects that voltage is present on the cruise control resume/accel switch signal circuit for longer than 90 seconds.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0567 Cruise Control Resume Switch Circuit
Conditions for Running the DTC
| • | The ignition is ON. |
| • | The cruise control switch is ON. |
Conditions for Setting the DTC
The ECM detects that the resume/accel switch is applied for longer than 90 seconds.
Action Taken When the DTC Sets
| • | The ECM stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The ECM records the operating conditions at the time the diagnostic fails. The ECM stores this information in the Failure Records. |
| • | The cruise control system is disabled. |
Conditions for Clearing the MIL/DTC
| • | A last test failed, or the current DTC, clears when the diagnostic runs and does not fail. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if failures are not reported by this or any other emission related diagnostic. |
| • | Use a scan tool in order to clear the MIL/DTC. |
Diagnostic Aids
| • | Ensure that the resume/accel switch is not stuck or sticking in the engaged position. |
| • | For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections . |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Cruise Control Schematics Connector End View Reference: Engine Control Module Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
Does the Cruise Resume/Accel. Switch parameter display On? | Go to Step 3 | Go to Diagnostic Aids | |
3 |
Does the Cruise Resume/Accel. Switch parameter display On? | Go to Step 4 | Go to Step 5 |
4 | Test the cruise control resume/accel switch signal circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 6 |
5 | Inspect for poor connections at the harness connector of the cruise control switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 7 |
6 | Inspect for poor connections at the harness connector of the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 8 |
7 | Replace the cruise control switch. Refer to Turn Signal Multifunction Switch Replacement . Did you complete the replacement? | Go to Step 9 | -- |
8 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 9 | -- |
9 |
Does the DTC reset? | Go to Step 2 | System OK |
