Important:  The Road Test Procedure should be performed only as part of the Functional Test Procedure. Refer to Functional Test .

The following test provides a method of evaluating the condition of the automatic transmission. The test is structured so that most driving conditions would be achieved. The test is divided into the following parts:

Important: Complete the test in the sequence given. Incomplete testing cannot guarantee an accurate evaluation.

Before the road test, ensure the following conditions are met:

During the road test:

After the road test, inspect the following conditions:

Perform this check first, in order to ensure the electronic transmission components are connected and functioning properly. If these components are not checked, a simple electrical condition could be mis-diagnosed.

1. Install the scan tool.
2. Ensure the shift selector is in PARK and set the parking brake.
3. Start the engine.
4. Verify that the following scan tool data can be obtained and is functioning properly. Refer to Scan Tool Data List for typical data values. Data that is questionable may indicate a concern.

•	Engine speed

•	Transmission input speed, turbine

•	Transmission output speed

•	Vehicle speed

•	C, D, E and REVERSE pressure switch states

•	Transmission range, engine list

•

4WD low

•	Commanded range, current range

•	A and B solenoid reference current

•	A and B solenoid actual current

•	A and B solenoid duty cycle

•	Brake switch

•	Engine coolant temperature

•	Transmission fluid temperature

•	Throttle angle

•	Ignition voltage

•	C shift solenoid ON/OFF

•	D shift solenoid ON/OFF

•	E shift solenoid ON/OFF

•	TCC solenoid duty cycle

•	TCC slip speed

5. Monitor the brake switch signal while depressing and releasing the brake pedal. The scan tool should display the following:

•	Closed when the brake pedal is released

•	Open when the brake pedal is depressed

6. Check the garage shifts.

6.1.	Apply the brake pedal and ensure the parking brake is set.

6.2.	Move the shift selector through the following ranges:

6.2.1.

PARK to REVERSE

6.2.2.

REVERSE to NEUTRAL

6.2.3.

NEUTRAL to DRIVE

6.3.	Pause 2 to 3 seconds in each selector position.

Important: Harsh engagement may be caused by any of the following conditions:    •  High idle speed          Compare engine idle speed to desired idle speed.    •  Commanded low A or B solenoid current          Compare A and B solenoid reference current to A and B solenoid actual current.    •  A default condition caused by certain DTCs that result in maximum full throttle shift points    •  Shift is not fully adapted

Important: Soft or delayed engagement may be caused by any of the following conditions:    •  Low idle speed          Compare engine idle speed to desired idle speed.    •  Low fluid level    •  Cold transmission fluid          Inspect for low transmission fluid temperature.

6.4.	Verify the range engagements are immediate and not harsh.

7. Monitor the transmission range on the scan tool engine list.

7.1.	Apply the brake pedal and ensure the parking brake is set.

7.2.	Move the shift selector through all ranges.

7.3.	Pause 2 to 3 seconds in each range.

7.4.	Return the shift selector to PARK.

7.5.	Verify that all of the selector positions match the scan tool display.

8. Inspect the throttle angle input.

8.1.	Apply the brake pedal and ensure the parking brake is set.

8.2.	Ensure the shift selector is in PARK.

8.3.	Monitor the throttle angle while increasing and decreasing the engine speed with the throttle pedal. The scan tool throttle angle should increase and decrease with the engine speed.

If any of the above checks do not perform properly, record the result for reference after the completion of the Road Test Procedure.

The transmission control module (TCM) calculates the upshift points based on the throttle angle and the engine, turbine and output speed. When the TCM determines that conditions are met for a shift to occur, the TCM commands the shift, and controls A and B solenoid current to proper control clutch pressures during the shift.

Perform the following steps:

1. Choose a throttle position of 10 percent, 25 percent or 50 percent. All throttle angles shown should be tested to cover the normal driving range.
2. Monitor the following scan tool parameters:

•	Throttle angle

•	Vehicle speed

•	Engine speed

•	Output shaft speed

•	Commanded range

•	Slip speed

•	Solenoid states

3. Place the shift selector in DRIVE.
4. Using the chosen throttle angle, accelerate the vehicle. Hold the throttle steady.
5. As the transmission upshifts, note the vehicle speed when the shift occurs for each range change. There should be a noticeable shift feel or engine speed change within 1 to 2 seconds of the commanded range change.
6. Shift speeds may vary slightly due to transmission fluid temperature or hydraulic delays in responding to the electronic controls.

•	Note any harsh, soft or delayed shifts or slipping.

•	Note any noise or vibration.

7. Repeat steps 1-6 to complete all throttle angles.

Important: The TCC will not engage until the engine is in closed loop operation. The vehicle must be in a near cruise condition, not accelerating or coasting, and on a level road surface.

8. Inspect for TCC apply in SECOND, THIRD, FOURTH and FIFTH range.

•	Note the TCC apply point. When the TCC applies there should be a noticeable drop in engine speed and a drop in slip speed to below 100 RPM. If the TCC apply can not be detected inspect for DTCs. Refer to Torque Converter Diagnosis .

•	Lightly tap and release the brake pedal. The TCC will release on most applications.

1. Place the shift selector in DRIVE.
2. Accelerate the vehicle to a speed just above the FOURTH to FIFTH shift point, using less than 50 percent throttle.
3. Quickly increase throttle angle to greater than 63 percent.
4. Verify the following conditions:

•	The TCC releases.

•	The transmission downshifts immediately to FOURTH range.

Manual 5-3 Downshift

1. Place the shift selector in DRIVE.
2. Accelerate the vehicle to obtain FIFTH range.
3. Release the throttle while moving the shift selector to THIRD.
4. Verify the following conditions:

•	The TCC releases.

•	The transmission downshifts immediately to FOURTH range and then to THIRD range.

•	The engine slows the vehicle.

Manual 5-2 Downshift

1. Place the shift selector in DRIVE.
2. Accelerate the vehicle to obtain FIFTH range.
3. Release the throttle while moving the shift selector to SECOND.
4. Verify the following conditions:

•	The TCC releases.

•	The transmission downshifts immediately to FOURTH range, then to THIRD, then to SECOND.

•	The engine slows the vehicle.

1. Place the shift selector in DRIVE.
2. Accelerate the vehicle until the 1-2 shift occurs.
3. Go to 8 km/h (5 mph) above the 1-2 shift point.
4. Release the throttle while moving the shift selector to FIRST.
5. Verify the following conditions:

•	The TCC releases.

•	The transmission immediately downshifts to FIRST range.

•	The engine slows the vehicle.

1. Place the shift selector in DRIVE.
2. Accelerate the vehicle to FIFTH range with the TCC applied.
3. Release the throttle and lightly apply the brakes.
4. Verify the following conditions:

•	The TCC releases.

•	Downshifts occur in normal sequence and the transmission returns to FIRST range before the vehicle comes to a stop.

The shift solenoids control the upshifts in the manual ranges.

Perform the following tests, using 10-15 percent throttle angle.

REVERSE

1. With the vehicle stopped, move the shift selector to REVERSE.
2. Slowly accelerate the vehicle.
3. Verify that there is no noticeable slip, noise or vibration.

Manual FIRST

1. With the vehicle stopped, move the shift selector to FIRST.
2. Accelerate the vehicle to maximum speed.
3. Verify the following conditions:

•	No upshifts occur.

•	The TCC does not apply.

•	There is no noticeable slip, noise, or vibration.

Manual SECOND

1. With the vehicle stopped, move the shift selector to SECOND.
2. Accelerate the vehicle to maximum speed.
3. Verify the following conditions:

•	The 1-2 shift occurs.

•	The 2-3 shift does not occur.

•	There is no noticeable slip, noise, or vibration.

Manual THIRD

1. With the vehicle stopped, move the shift selector to THIRD.
2. Accelerate the vehicle to maximum speed.
3. Verify the following conditions:

•	The 1-2 shift occurs.

•	The 2-3 shift occurs.

•	There is no noticeable slip, noise, or vibration.