GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

Notice: In order to prevent damage to the crankshaft position (CKP) sensor reluctor wheel/ring, care must be used when removing or installing this component.


    Object Number: 856643  Size: SH
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the fuel line bracket nut (2).
  3. Remove the fuel line bracket from the bellhousing stud.
  4. Lower the vehicle.

  5. Object Number: 674728  Size: SH
  6. Remove the driver side rear ignition coil bolts.
  7. Reposition the ignition coil.
  8. Disconnect the crankshaft position (CKP) sensor electrical connector.
  9. Use penetrating oil and allow the oil to soak around the CKP sensor prior to removing the sensor.

  10. Object Number: 858216  Size: SH
  11. Remove the CKP sensor bolt.
  12. Twist the CKP sensor back and forth.
  13. Pull the sensor straight up in order to remove the CKP sensor.

  14. Object Number: 814961  Size: SH
  15. Inspect the CKP sensor for wear.
  16. Important: The CKP sensor is designed to contact the reluctor wheel of the crankshaft. Wear may be noticeable on the end of the sensor.

  17. Normal CKP sensor wear will be shown on the wear strips (1) and no wear will be shown on the sensor sensing element (2).

  18. Object Number: 814962  Size: SH
  19. Excessive or abnormal sensor wear will be shown on the sensing element (2).
  20. If excessive/abnormal wear is present, replace the sensor.

Installation Procedure


    Object Number: 858216  Size: SH
  1. If reusing the old sensor, Inspect both O-rings for cuts, cracks, tears or damage, replace the O-rings as needed.
  2. Lubricate the CKP sensor O-rings with clean engine oil.
  3. Important: Ensure that the CKP sensor is fully seated against the crankshaft reluctor ring. The upper flange on the sensor MAY NOT seat against the engine block.

  4. Install the CKP sensor.
  5. Important: The CKP sensor bolt has adhesive applied to the threads. The adhesive may have come off during removal of the bolt. Ensure that the bolt hole is clean of any debris before installing the reinstalling bolt.

  6. If reusing the old sensor, apply thread adhesive GM P/N 12345493 (Canadian P/N 10953488) or equivalent to the threads.
  7. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  8. Install the CKP sensor bolt.
  9. Tighten
    Tighten the bolt to 12 N·m (106 lb in).


    Object Number: 674728  Size: SH
  10. Connect the CKP sensor electrical connector.
  11. Position the ignition coil to the rocker cover.
  12. Install the driver side rear ignition coil bolts.
  13. Tighten
    Tighten the bolts to 12 N·m (106 lb in).


    Object Number: 856643  Size: SH
  14. Raise the vehicle
  15. Install the fuel line bracket to the bellhousing stud.
  16. Install the fuel line bracket nut (2).
  17. Tighten
    Tighten the nut to 10 N·m (89 lb in).

  18. Lower the vehicle.
  19. Perform the CKP system variation learn procedure. Refer to Crankshaft Position System Variation Learn .