Notice: If a turbocharger has failed, clean any turbocharger debris or excessive oil from the charge air cooler system before installing the new turbocharger. Failure to clean debris from the charge air cooler system will cause severe turbocharger and engine damage upon startup. Failure to clean excessive oil from the charge air cooler system may cause an engine runaway condition on startup, resulting in severe engine damage.

Important: If a turbocharger failure is thought to be caused due to lack of oil, the camshaft bearing should be checked. The number 4 camshaft bearing bore feeds the turbocharger oil supply (feed) pipe. If this camshaft bearing spins in the bore, the turbocharger will be starved for oil. This will cause a failure of the turbocharger. Failure to diagnosis this condition will result in repeat turbocharger failures.

1. Disconnect both battery negative cables. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
2. Move the hood to the service position by moving the hood hinge bolts (1) to the service positions (2).



3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
4. Remove the exhaust pipe to the exhaust outlet clamp. Move the clamp onto the exhaust pipe.



5. If equipped with an automatic transmission, remove the transmission fluid fill tube to bell housing nuts.
6. Position the transmission fluid fill tube to the right side of the vehicle. The tube does not require removal from the transmission.



7. Remove the 3 nuts (2) and the left exhaust heat shield (3) at the front of the lower dash panel.



8. Remove the left exhaust pipe heat shield bolts.
9. Position the left exhaust pipe heat shield in order to access the left exhaust pipe to exhaust manifold bolts. Do not remove the heat shield from the vehicle at this time.




Important: Do not bend the exhaust pipe at the expansion area.

10. Remove the left exhaust pipe to exhaust manifold bolts (2).
11. Remove and discard the gasket.




Important: Do not bend the exhaust pipe at the expansion area.

12. Remove the right exhaust pipe to exhaust manifold bolts (1).
13. Remove and discard the gasket.



14. Remove the lower bolt (2) for the exhaust outlet shield.
15. Lower the vehicle.



16. Loosen the outlet duct clamp at the upper intake manifold cover.
17. Remove the upper intake manifold cover from the outlet duct.
18. Remove upper intake manifold cover.
19. Drain the engine coolant. Refer to Cooling System Draining and Filling in Engine Cooling.



20. Loosen the outlet duct clamps at the turbocharger and the mass air flow/intake air temperature sensor (MAF/IAT) sensor.
21. Remove the outlet duct from the turbocharger and MAF/IAT sensor.




Important: After removing the charged air cooler ducts, cover the turbocharger openings and the ducts with tape to prevent entry of objects.

22. Loosen both of the charged air cooler outlet duct to intake hose clamps.

Important: Do not use a screw driver or other tool to pry the hose loose. The hose can be torn or damage. Loosen the hose by twisting.

23. Remove the hose from the charged air cooler duct to the intake manifold tube.



24. Loosen the charged air cooler inlet duct to turbocharger cool air outlet clamp.

Important: Do not use a screw driver or other tool to pry the hose loose. The hose can be torn or damage. Loosen the hose by twisting.

25. Remove the charged air cooler inlet duct to turbocharger cool air outlet hose from the turbocharger.



26. Disconnect the A/C compressor clutch electrical connector.
27. Disconnect the A/C cut out switch electrical connector.
28. Remove the drive belt. Refer to Drive Belt Replacement .
29. Remove the A/C compressor mounting bolts.
30. Move the A/C compressor with the hoses attached to the right side of the engine compartment.



31. Disconnect the turbocharger inlet coolant hose from the turbocharger coolant bypass valve.



32. Disconnect the turbocharger outlet coolant hose from the turbocharger.



33. Disconnect the PCV hose from the left valve rocker arm cover.
34. Position the hose out of the way.
35. Remove the wire connector from the intake heater.
36. If equipped, remove the intake air heater relay. Refer to Intake Air Heater Relay Replacement in Engine Controls - 6.6L.



37. Remove the 3 bolts holding the heat shield to the turbocharger.
38. Remove the turbocharger heat shield.



39. Remove the remaining 2 bolts (1, 3) for the exhaust outlet heat shield.
40. Remove the exhaust outlet heat shield.



41. Remove the 4 bolts and the 2 nuts for the exhaust outlet.

Important: The exhaust outlet does not require removal in order to remove the turbocharger.

42. Move the exhaust outlet to one side in order to access the right exhaust pipe to turbocharger bolts.
43. Remove and discard the exhaust outlet gasket.



44. Remove the right exhaust pipe to turbocharger bolts (2).
45. Remove the right exhaust pipe.
46. Remove and discard the gasket.



47. Move the exhaust outlet to one side in order to access the left exhaust pipe.
48. Remove the left exhaust pipe heat shield from the vehicle.
49. Remove the left exhaust pipe to turbocharger bolts (1).
50. Remove the left exhaust pipe.
51. Remove and discard the gasket.




Notice: Do not twist the turbocharger oil feed pipe. Twisting of the feed pipe will result in the collapse and deformation of the plastic pipe, restricting oil flow and causing turbocharger damage. During turbocharger replacement, gently push the oil feed pipe towards the front of the engine to clear the turbocharger. Assistance may be required to keep the pipes clear of the turbocharger during removal or installation.

52. Remove the turbocharger oil feed pipe eye bolt, and washers.
53. Move the oil feed pipe out of the way.



54. Remove the turbocharger oil return pipe nuts at the flywheel housing.



55. Remove the turbocharger mounting bolts.
56. Remove the turbocharger with the turbocharger oil return pipe.



57. If necessary, remove the turbocharger lower heat shield.
58. If necessary, remove the turbocharger oil feed pipe bolt, washers, and pipe.
59. If the turbocharger has failed, perform the following steps the verify the condition of the number 4 camshaft bearing before installing a new turbocharger.

59.1.

Visually inspect for correct alignment of the number 4 camshaft bearing oil hole through the turbocharger oil supply hole in the block.

59.2.

Turn the engine over by hand 1/2 turn and inspect for camshaft bearing movement, indicating a spun camshaft bearing.

59.3.

If the bearing is spun the engine MUST be replaced.




60. If replacing the turbocharger remove the following items:

•	Oil return pipe

•	Coolant hose

61. Clean the following gasket surfaces:

•	Oil drain pipe to turbocharger

•	Oil drain pipe to flywheel housing

•	Air intake tube

•	Both exhaust pipe flanges

•	Both exhaust manifold flanges

•	Exhaust outlet

•	Turbocharger, exhaust outlet

•	Turbocharger, both exhaust pipe

1. Install the turbocharger oil drain pipe and NEW gasket to the turbocharger.

Notice: Refer to Fastener Notice in the Preface section.

2. Install the turbocharger oil drain pipe bolts.

Tighten
Tighten the oil drain pipe bolts to 21 N·m (16 lb ft).

3. Install the turbocharger inlet coolant hose to the turbocharger.




Notice: Do not twist the turbocharger oil feed pipe. Twisting of the feed pipe will result in the collapse and deformation of the plastic pipe, restricting oil flow and causing turbocharger damage. During turbocharger replacement, gently push the oil feed pipe towards the front of the engine to clear the turbocharger. Assistance may be required to keep the pipes clear of the turbocharger during removal or installation.

4. Install the turbocharger oil feed pipe to the engine block.
5. Install the turbocharger oil feed pipe eye bolt and washers.

Tighten
Tighten the turbocharger oil feed pipe eye bolt to 34 N·m (25 lb ft).

6. Install the turbocharger lower heat shield to the engine block.



7. Install the turbocharger to the engine.
8. Install the turbocharger 3 mounting bolts.

Tighten
Tighten the turbocharger mounting bolts to 108 N·m (80 lb ft).




9. Install a NEW gasket for the oil drain pipe.
10. Install the turbocharger oil drain pipe nuts.

Tighten
Tighten the turbocharger drain pipe nuts to 21 N·m (15 lb ft).




11. If installing a new turbocharger, pour about 120-150 cc (4-5 oz) of clean engine oil in the turbocharger oil feed pipe opening while rotating the impeller.
12. Using NEW sealing washers, install the oil feed pipe and bolt to the turbocharger.

Tighten
Tighten the oil feed pipe eye bolt to 34 N·m (25 lb ft).




13. Position the left exhaust pipe. The pipe flanges are different. Ensure the proper pipe flange is towards the turbocharger.
14. Install the left exhaust pipe to the turbocharger with NEW gasket. Align the gasket at the turbocharger with the tab on the gasket facing inward. To aid in installing the pipe to the turbocharger temporarily install one of the pipe to manifold bolts.

Tighten
Tighten the left exhaust pipe to turbocharger bolts (1) to 53 N·m (39 lb ft).

15. Position the left exhaust pipe heat shield, but do not install the bolts.



16. Install the right exhaust pipe with NEW gasket to the turbocharger. Align the gasket at the turbocharger with the tab on the gasket facing inward. To aid in installing the pipe to the turbocharger temporarily install one of the pipe to manifold bolts.
17. Install the right exhaust pipe to turbocharger bolts (2).

Tighten
Tighten the right exhaust pipe to turbocharger bolts to 53 N·m (39 lb ft).




18. Install the exhaust outlet with a NEW gasket to the turbocharger.
19. Install the exhaust outlet bolts and nuts.

Tighten
Tighten the exhaust outlet bolts and nuts to 53 N·m (39 lb ft).




20. Install the exhaust outlet heat shield.
21. Install the upper 2 exhaust outlet heat shield bolts (1, 3).

Tighten
Tighten the exhaust outlet heat shield bolts to 8 N·m (71 lb in).




22. Install the turbocharger heat shield.
23. Install the turbocharger heat shield bolts.

Tighten
Tighten the turbocharger heat shield bolts to 9 N·m (80 lb in).




24. Connect the PCV hose to the upper left valve rocker arm cover.



25. Connect the turbocharger outlet coolant hose to the turbocharger.



26. Connect the turbocharger inlet coolant hose to the turbocharger coolant bypass valve.
27. Install the inlet air heater relay. Refer to Intake Air Heater Relay Replacement in Engine Controls - 6.6L.
28. Connect the wire terminal and the nut to intake air heater.

Tighten
Tighten the intake air heater nut to 4 N·m (35 lb in).




29. Position the A/C compressor.
30. Install the A/C compressor mounting bolts.

Tighten
Tighten the A/C compressor mounting bolts to 50 N·m (37 lb ft).

31. Install the drive belt. Refer to Drive Belt Replacement
32. Connect the A/C cut out switch electrical connector.
33. Connect the A/C clutch electrical connector.



34. Install the charged air cooler inlet duct to turbocharger cool air outlet hose to the turbocharger.
35. Position the clamp as shown for proper clearance.

Tighten
Tighten the clamp to 6 N·m (53 lb in).




36. Install the hose to the charged air cooler outlet duct to intake manifold tube.

The hose is marked DUCT which connects to the charged air cooler outlet duct.

The hose is marked ENG which connects to the turbocharger.

Align the marks on the hose with the alignment marks on the pipe and tube.

37. Position the clamps as shown for proper clearance.

Tighten
Tighten the clamps to 6 N·m (53 lb in).





Important: The outlet duct must be fully seated against the positive stop feature on the turbocharger inlet.

38. Install the outlet duct to the turbocharger.
39. Align the outlet duct alignment indicator (1) to the turbocharger alignment indicator (2).




Important: The outlet duct must be fully seated against the MAF/IAT sensor with the edge of the seal in the vertical position.

40. Install the outlet duct to the MAF/IAT sensor.
41. Tighten the outlet duct clamps at the turbocharger and the MAF/IAT sensor.

Tighten
Tighten the clamps to 6 N·m (53 lb in).




42. Raise the vehicle.
43. Install the lower bolt (2) for the exhaust outlet heat shield.

Tighten
Tighten the exhaust outlet heat shield bolt to 8 N·m (71 lb in).




44. Install the right exhaust pipe with a NEW gasket to exhaust manifold. Align the tab on the exhaust pipe gasket facing outward.
45. Install the right exhaust pipe bolts (2).

Tighten
Tighten the exhaust pipe to exhaust manifold bolts to 53 N·m (39 lb ft).




46. Install the left exhaust pipe with a NEW gasket to exhaust manifold. Align the tab on the exhaust pipe gasket facing outward.
47. Install the left exhaust pipe bolts (1).

Tighten
Tighten the exhaust pipe to exhaust manifold bolts to 53 N·m (39 lb ft).




48. Position the left exhaust pipe heat shield.
49. Install the left exhaust pipe heat shield bolts.

Tighten
Tighten the left exhaust pipe heat shield bolts to 8 N·m (71 lb ft).




50. Install the exhaust heat shield (3) to left front of the dash panel.
51. Install the shield nuts (2).

Tighten
Tighten the shield nuts to 9 N·m (80 lb ft).




52. If equipped position the transmission fluid fill tube.
53. Install the transmission fluid fill tube nuts.

Tighten
Tighten the transmission fluid fill tube nuts to 18 N·m (13 lb ft).




54. Install the exhaust outlet to exhaust pipe clamp.

To assist in positioning the clamp on the flanges use a suitable screw jack to hold the exhaust pipe in position.

Tighten
Tighten the exhaust pipe clamp to 40 N·m (30 lb ft).

55. Lower the vehicle.
56. Fill the cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.



57. Install the upper intake manifold cover.
58. Install the upper intake manifold cover to the outlet duct.
59. Tighten the outlet duct clamp at the upper intake manifold cover.

Tighten
Tighten the clamp to 6 N·m (53 lb in).




60. Position the hood in the normal operating position by moving the hood hinge bolts from service position (2) to normal operating position (1).

Tighten
Tighten the hood hinge bolts to 25 N·m (18 lb ft).

61. Connect both battery negative cables. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
62. Road test the vehicle for normal operation.
63. Inspect for coolant, oil, or exhaust leaks.