DTC P1860 TCC PWM Solenoid Circuit Electrical Gas LQ4
Circuit Description
The torque converter clutch pulse width modulation (TCC PWM) solenoid valve controls fluid acting on the converter clutch valve, which then controls TCC apply and release. The TCC PWM solenoid valve attaches to the control valve body within the transmission. Ignition voltage goes directly to the TCC PWM solenoid valve. The powertrain control modulator (PCM) controls the TCC PWM solenoid valve by providing a ground path on circuit 418. The current flows through the TCC PWM solenoid valve coil according to the duty cycle (percentage of ON time). The TCC PWM solenoid valve provides a smooth engagement of the torque converter clutch by operating on a duty cycle percent of ON time.
If the PCM detects a continuous open or short in the TCC PWM solenoid valve circuit or the TCC PWM solenoid valve, then DTC P1860 sets. DTC P1860 is a type C DTC. For California emission vehicles DTC P1860 is a type A DTC.
Conditions for Running the DTC
| • | The system voltage is 8.0-18.0 volts. |
| • | The engine is running greater than 300 RPM for greater than 7 seconds. |
| • | No shift solenoid DTCs P0751, P0753, P0756, or P0758. |
Conditions for Setting the DTC
All conditions for running the DTC are met, and either of the following conditions occur for 4.3 out of 5 seconds.
| • | The PCM commands the TCC PWM solenoid valve to OFF (0%) and the voltage input remains low (zero volts). |
| • | The PCM commands the TCC PWM solenoid valve to ON (100%) and the voltage input remains high (B+). |
Action Taken When the DTC Sets
| • | The PCM illuminates the malfunction indicator lamp for California emission vehicles. |
| • | The PCM inhibits TCC engagement. |
| • | The PCM inhibits 4th gear if TFT is greater than 130°C (266°F). |
| • | The PCM freezes shift adapts from being updated. |
| • | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame (Calif. only) and Failure Records (Calif. and Federal). |
| • | The PCM stores DTC P1860 in PCM history. |
Conditions for Clearing the MIL/DTC
| • | For California emissions, the PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
| • | A scan tool can clear the MIL/DTC. |
| • | For California emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without an emission related diagnostic fault occurring. |
| • | For Federal emissions, the PCM clears the DTC from PCM history if the vehicle completes 40 consecutive warm-up cycles without a non-emission related diagnostic fault occurring. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | First diagnose and clear any engine DTCs or TP sensor codes that are present. Then inspect for any transmission DTCs that may have reset. |
| • | Inspect the connectors at the PCM, the AT wiring harness and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Wiring Systems. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for voltage to the TCC PWM solenoid valve circuit at the 20-way connector.
-
This step tests the ability of the PCM and wiring to control the ground circuit.
-
This step tests the resistance of the TCC PWM solenoid valve and the internal wiring harness.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | ||||||||
2 |
Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM. Is the fuse open? | -- | ||||||||
3 | Inspect the following components for a short to ground.
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Diagnostic Aids | |||||||
Does the test lamp illuminate? | -- | |||||||||
5 | Repair the open or high resistance in the power feed circuit (CKT 1020) of the TCC PWM solenoid valve. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | -- | |||||||
Does the test lamp turn ON when you command the TCC PWM solenoid valve ON, and does the lamp turn OFF when you command the TCC PWM solenoid valve OFF? | -- | |||||||||
7 |
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||||
Does the resistance measure within the specified values? | 10-15ohms | |||||||||
9 | Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls. Did you complete the replacement? | -- | -- | |||||||
10 |
Does the resistance measure within the specified values? | 10-15ohms | ||||||||
11 |
Do both readings measure greater than the specified value? | 250kohms | Go to Diagnostic Aids | |||||||
12 | Test the AT wiring harness assembly for an open circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | -- | |||||||
13 |
Do both readings measure greater than the specified value? | 250kohms | ||||||||
14 | Test the automatic transmission wiring harness assembly for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | -- | |||||||
15 | Replace the TCC PWM solenoid valve. Refer to Control Valve Body Replacement . Did you complete the replacement? | -- | -- | |||||||
16 | Replace the automatic transmission wiring harness assembly. Refer to Wiring Harness Replacement. Did you complete the replacement? | -- | -- | |||||||
17 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | System OK |
