GM Service Manual Online
For 1990-2009 cars only

Removal Procedure


    Object Number: 664828  Size: SH
  1. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Disconnect the connector position assurance (CPA) retainer.
  3. Notice: Do not remove the pigtail from either the heated oxygen sensor (HO2S) or the oxygen sensor (O2S). Removing the pigtail or the connector will affect sensor operation.

    Handle the oxygen sensor carefully. Do not drop the HO2S. Keep the in-line electrical connector and the louvered end free of grease, dirt, or other contaminants. Do not use cleaning solvents of any type.

    Do not repair the wiring, connector or terminals. Replace the oxygen sensor if the pigtail wiring, connector, or terminal is damaged.

    This external clean air reference is obtained by way of the oxygen sensor signal and heater wires. Any attempt to repair the wires, connectors, or terminals could result in the obstruction of the air reference and degraded sensor performance.

    The following guidelines should be used when servicing the heated oxygen sensor:

       • Do not apply contact cleaner or other materials to the sensor or vehicle harness connectors. These materials may get into the sensor causing poor performance.
       • Do not damage the sensor pigtail and harness wires in such a way that the wires inside are exposed. This could provide a path for foreign materials to enter the sensor and cause performance problems.
       • Ensure the sensor or vehicle lead wires are not bent sharply or kinked. Sharp bends or kinks could block the reference air path through the lead wire.
       • Do not remove or defeat the oxygen sensor ground wire, where applicable. Vehicles that utilize the ground wired sensor may rely on this ground as the only ground contact to the sensor. Removal of the ground wire will cause poor engine performance.
       • Ensure that the peripheral seal remains intact on the vehicle harness connector in order to prevent damage due to water intrusion. The engine harness may be repaired using Packard's Crimp and Splice Seals Terminal Repair Kit. Under no circumstances should repairs be soldered since this could result in the air reference being obstructed.

  4. Remove the heated oxygen sensor (HO2S) connector clip from the frame.
  5. If equipped with a 4.8L or 5.3L engine, disconnect the HO2S electrical connector.

  6. Object Number: 694907  Size: SH
  7. If equipped with a 6.0L engine, disconnect the HO2S electrical connector.

  8. Object Number: 664954  Size: SH
  9. Remove the HO2S.

Installation Procedure

Important: A special anti-seize compound is used on the HO2S threads. The compound consists of liquid graphite and glass beads. The graphite tends to burn away, but the glass beads remain, making the sensor easier to remove. New, or service replacement sensors already have the compound applied to the threads. If the sensor is removed from an exhaust component and if for any reason the sensor is to be reinstalled, the threads must have anti-seize compound applied before the reinstallation.


    Object Number: 664954  Size: SH
  1. If reinstalling the old sensor, coat the threads with anti-seize compound GM P/N 12377953, or equivalent.
  2. Notice: Replacement components must be the correct part number for the application. Components requiring the use of the thread locking compound, lubricants, corrosion inhibitors, or sealants are identified in the service procedure. Some replacement components may come with these coatings already applied. Do not use these coatings on components unless specified. These coatings can affect the final torque, which may affect the operation of the component. Use the correct torque specification when installing components in order to avoid damage.

  3. Install the HO2S.
  4. Tighten
    Tighten the sensor to 42 N·m (31 lb ft).


    Object Number: 694907  Size: SH
  5. If equipped with a 6.0L engine, connect the HO2S electrical connector.

  6. Object Number: 664828  Size: SH
  7. If equipped with a 4.8L or 5.3L engine, connect the HO2S electrical connector.
  8. Install the HO2S connector clip to the frame.
  9. Disconnect the CPA retainer.
  10. Lower the vehicle.