GM Service Manual Online
For 1990-2009 cars only

Fuel Injection Fuel Rail Assembly Replacement 4.8L, 5.3L, and 6.0L Engines

Removal Procedure

Important:  An 8-digit identification number (1) is located on the fuel rail. Refer to this identification number when servicing or when part replacement is required.


    Object Number: 380659  Size: SH
  1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief .

  2. Object Number: 663672  Size: SH
  3. Remove the wire harness bracket nut (2).
  4. Disconnect the evaporative emission (EVAP) purge solenoid electrical connector (1).
  5. Disconnect the generator electrical connector (3).

  6. Object Number: 679510  Size: SH
  7. Disconnect the following electrical connectors:
  8. • Manifold absolute pressure (MAP) sensor (1)
    • Knock sensor (2)
  9. Remove the knock sensor harness connector from the intake manifold.

  10. Object Number: 757686  Size: SH
  11. Remove the connector position assurance (CPA) lock.
  12. Disconnect the following electrical connectors from both sides of the engine:
  13. • Main coil (2)
    • Fuel injectors
  14. Remove the harness clips from the fuel rail (1).
  15. Reposition the engine wire harness aside.

  16. Object Number: 820977  Size: SH
  17. Perform the following steps in order to disconnect the fuel injector electrical connectors.
  18. 11.1. Mark the connectors to their corresponding injectors to ensure correct reassembly.
    11.2. Pull the connector position assurance (CPA) retainer (2) on the connector up 1 click.
    11.3. Push the tab (1) on the connector in.
    11.4. Disconnect the fuel injector electrical connector.
    11.5. Repeat the steps for each injector electrical connector.

    Object Number: 647793  Size: SH
  19. Remove the positive crankcase ventilation (PCV) hose.

  20. Object Number: 856643  Size: SH
  21. Disconnect the fuel feed and return pipes (1) from the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .
  22. Remove the fuel pressure regulator vacuum hose.

  23. Object Number: 376389  Size: MH
  24. Remove the fuel rail bolts.
  25. Notice: 

       • Remove the fuel rail assembly carefully in order to prevent damage to the injector electrical connector terminals and the injector spray tips. Support the fuel rail after the fuel rail is removed in order to avoid damaging the fuel rail components.
       • Cap the fittings and plug the holes when servicing the fuel system in order to prevent dirt and other contaminants from entering open pipes and passages.

    Important: Before removal, clean the fuel rail with a spray type engine cleaner, such as GM X-30A or equivalent, if necessary. Follow the package instructions. Do not soak the fuel rail in liquid cleaning solvent.

  26. Remove the fuel rail.

  27. Object Number: 351185  Size: SH
  28. Remove the fuel injector lower O-ring seal (4) from each injector, if necessary.
  29. Discard the O-ring seal.

Installation Procedure


    Object Number: 351185  Size: SH
  1. Lubricate NEW fuel injector lower O-ring seals (4) with clean engine oil.
  2. Install the NEW O-ring seals (4) onto each injector, if necessary.

  3. Object Number: 376389  Size: MH
  4. Install the fuel rail.
  5. Apply a 5 mm (0.2 in) band of threadlock GM P/N 12345382 (Canadian 10953489), or equivalent to the threads of the fuel rail bolts.
  6. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  7. Install the fuel rail bolts.
  8. Tighten
    Tighten the bolts to 10 N·m (89 lb in).


    Object Number: 856643  Size: SH
  9. Install the fuel pressure regulator vacuum hose.
  10. Connect the fuel feed and return pipes (1) to the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .

  11. Object Number: 647793  Size: SH
  12. Install the PCV hose.

  13. Object Number: 820977  Size: SH
  14. Perform the following steps in order to connect the fuel injector electrical connectors.
  15. 9.1. Install the connectors to their corresponding injectors to ensure correct reassembly.
    9.2. Connect the fuel injector electrical connector.
    9.3. Push the CPA retainer (2) on the connector in 1 click.
    9.4. Repeat the steps for each injector electrical connector.

    Object Number: 757686  Size: SH
  16. Position the engine wire harness.
  17. Connect the following electrical connectors to both sides of the engine:
  18. • Main coil (2)
    • Fuel injectors
  19. Install the harness clips to the fuel rail (1).
  20. Install the CPA retainers.

  21. Object Number: 679510  Size: SH
  22. Connect the following electrical connectors:
  23. • MAP sensor (1)
    • Knock sensor (2)
  24. Install the knock sensor harness connector to the intake manifold.

  25. Object Number: 663672  Size: SH
  26. Connect the EVAP purge solenoid electrical connector (1).
  27. Connect the generator electrical connector (3).
  28. Install the wire harness bracket nut (2).
  29. Tighten
    Tighten the nut to 5 N·m (44 lb in).

  30. Tighten the fuel fill cap.
  31. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  32. Use the following procedure in order to inspect for leaks:
  33. 21.1. Turn the ignition ON, with the engine OFF, for 2 seconds.
    21.2. Turn the ignition OFF for 10 seconds.
    21.3. Turn the ignition ON, with the engine OFF.
    21.4. Inspect for fuel leaks.

Fuel Injection Fuel Rail Assembly Replacement 5.3L, VIN Z (RPO L59) Engine

Removal Procedure

    Important: The L59 E85 fuel rail is comprised of a material that is compatible with fuel that has a concentration of up to 85 percent ethanol. The E85 fuel rail also uses an E85 Denso fuel injectors. Because of this, special procedures will be used in servicing the fuel rail and associated components. The screws that fasten the retaining clips for the crossover pipe to the fuel rails are thread cutting and therefore should NOT be removed from the fuel rail. The fuel rail will be serviced as an entire component.

    Important:  An 8-digit identification number (1) is located on the fuel rail. Refer to this model identification number if service or part replacement is required.


    Object Number: 380659  Size: SH
  1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief .

  2. Object Number: 663672  Size: SH
  3. Remove the wire harness bracket nut (2).
  4. Disconnect the evaporative emission (EVAP) purge solenoid electrical connector (1).
  5. Disconnect the generator electrical connector (3).

  6. Object Number: 679510  Size: SH
  7. Disconnect the following electrical connectors:
  8. • Manifold absolute pressure (MAP) sensor (1)
    • Knock sensor (2)
  9. Remove the knock sensor harness connector from the intake manifold.

  10. Object Number: 757686  Size: SH
  11. Remove the connector position assurance (CPA) retainer.
  12. Disconnect the following electrical connectors from both sides of the engine:
  13. • Main coil (2)
    • Fuel injectors
  14. Remove the harness clips from the fuel rail (1).
  15. Reposition the upper engine wire harness aside.

  16. Object Number: 820977  Size: SH
  17. Perform the following steps in order to disconnect the fuel injector electrical connectors:
  18. Important: When disconnecting the Multec® 2 fuel injector connectors, DO NOT use pliers or other hand tools, as the connector ends may become mangled and be rendered unusable.

    11.1. Mark the connectors to their corresponding injectors to ensure correct reassembly.
    11.2. Pull the connector position assurance (CPA) retainer (2) on the connector up 1 click.
    11.3. Push the tab (1) on the connector in.
    11.4. Disconnect the fuel injector connector electrical connector.
    11.5. Repeat the steps for each injector connector.

    Object Number: 647793  Size: SH
  19. Remove the positive crankcase ventilation (PCV) hose.

  20. Object Number: 856643  Size: SH
  21. Disconnect the fuel feed and return pipes (1, 2) from the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .
  22. Disconnect the fuel pressure regulator vacuum line.

  23. Object Number: 260176  Size: SH
  24. Remove the fuel rail bolts.
  25. Notice: 

       • Remove the fuel rail assembly carefully in order to prevent damage to the injector electrical connector terminals and the injector spray tips. Support the fuel rail after the fuel rail is removed in order to avoid damaging the fuel rail components.
       • Cap the fittings and plug the holes when servicing the fuel system in order to prevent dirt and other contaminants from entering open pipes and passages.

    Important: Before removal, if necessary, clean the fuel rail assembly with a spray type engine cleaner, use GM X-30A or equivalent. Follow the package instructions. Do not soak fuel rail assembly in any liquid cleaning solvents.

  26. Remove the fuel rail.

  27. Object Number: 351185  Size: SH
  28. Remove the fuel injector lower O-ring seals (4) from each injector, if necessary.
  29. Discard the O-ring seal.

Installation Procedure


    Object Number: 351185  Size: SH
  1. Lubricate the NEW fuel injector lower O-ring seals (4) with clean engine oil.
  2. Install the NEW O-ring seals (4) onto each injector, if necessary.

  3. Object Number: 376389  Size: MH
  4. Install the fuel rail.
  5. Apply a 5 mm (0.020 in) band of threadlock, GM P/N 12345382 (Canadian P/N 10953489), or equivalent, to the threads of the fuel rail bolts.
  6. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  7. Install the fuel rail bolts.
  8. Tighten
    Tighten the bolts to 10 N·m (89 lb in).


    Object Number: 856643  Size: SH
  9. Connect the fuel pressure regulator vacuum line.
  10. Connect the fuel feed and return pipes (1, 2) to the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .

  11. Object Number: 647793  Size: SH
  12. Install the PCV hose.

  13. Object Number: 820977  Size: SH
  14. Perform the following steps in order to connect the fuel injector electrical connectors.
  15. 9.1. Install the connectors to their corresponding injectors to ensure correct reassembly.
    9.2. Connect the fuel injector electrical connector.
    9.3. Push the CPA retainer (2) in the connector in 1 click.
    9.4. Repeat the steps for each injector electrical connector.

    Object Number: 757686  Size: SH
  16. Position the engine wire harness.
  17. Connect the following electrical connectors to both sides of the engine:
  18. • Main coil (2)
    • Fuel injectors
  19. Install the harness clips to the fuel rail (1).
  20. Install the CPA retainers.

  21. Object Number: 679510  Size: SH
  22. Connect the following electrical connectors:
  23. • MAP sensor (1)
    • Knock sensor (2)
  24. Install the knock sensor harness connector to the intake manifold.

  25. Object Number: 663672  Size: SH
  26. Connect the EVAP purge solenoid electrical connector (1).
  27. Connect the generator electrical connector (3).
  28. Install the wire harness bracket nut (2).
  29. Tighten
    Tighten the nut to 5 N·m (44 lb in).

  30. Tighten the fuel fill cap.
  31. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  32. Use the following procedure in order to inspect for leaks:
  33. 21.1. Turn the ignition ON, with the engine OFF, for 2 seconds.
    21.2. Turn the ignition OFF for 10 seconds.
    21.3. Turn the ignition ON, with the engine OFF.
    21.4. Inspect for fuel leaks.