Exhaust Moan/Vibration Noise (Install Exhaust System Flex Pipe Kit and Exhaust Dampeners, If Necessary)

This bulletin is being revised to add the 2007 and 2008 (New Body Style) model years, update the warranty information and add information for installing exhaust dampeners. Please discard Corporate Bulletin Number 02-06-05-003F (Section 06 -- Engine/Propulsion System).

Some customers may comment on a moan or vibration noise at low vehicle speeds 40-64 km (25-40 mph) or between 900-1700 RPM under load.

Exhaust system resonance may be transmitted through the powertrain mounts into the body causing this condition.

Caution:  Personal injury or burns may occur when working on a hot exhaust system, let the exhaust system cool off prior to performing the repair.

An exhaust system flex pipe kit is available to correct this condition. If diagnosis leads to this condition, install the applicable exhaust system flex pipe kit listed below using the following procedure. Refer to the Parts Information for kit applications and usage.

Important: This fix and the kit part numbers are specific to vehicle frame type. A Level 3 frame was introduced interim 2000 model year (approximately January 2000). With a Level 3 frame, the transmission crossmember was moved forward of its previous location. Pre-Level 3 frames will require the installation of additional components to correct the condition.

1999-2000 4WD Models Built Prior to 1/20/00 and All 2000-2008 2WD and 4WD Models Built After 1/00

These models require the installation of a flex coupling. The flex coupling has adapter sleeves for the installation of U-bolt clamps. This procedure uses the U-bolt clamps, but the preferred installation method is to weld the flex coupler to the exhaust pipe.

1. Raise the vehicle.
2. Locate the first available straight section of pipe rearward of the mid-joint flange and forward of the muffler assembly.
3. Measure approximately 228 mm (9 in) on the straight pipe and mark.
4. Using a suitable cutting tool, cut out the marked section of the pipe and remove.
5. Remove any burrs, if necessary, before installing the flex coupler pipe.



6. Install the flex coupling (1). Expand the sleeves of the flex coupler, if necessary, to properly fit over each pipe end. The centerline of the installed flex coupling should run parallel to the straight section of pipe (no bends in the coupling) for optimum performance.
7. Install the U-bolt clamps (2) on each sleeve end of the flex coupling.

Tighten
Tighten the U-bolt clamps to 30 N·m (22 lb ft).

8. Lower the vehicle.
9. Verify that the condition has been fixed.

If the exhaust vibration or moan is still present, order two exhaust dampeners, P/N 10199232, and proceed to Installation of Exhaust Dampeners, If Necessary in this bulletin.

Installation of Exhaust Dampeners, If Necessary

1. Locate the bend in the exhaust pipe over the rear axle.
2. Measure 102 mm (4 in) back on the straight portion of the exhaust pipe and mark the location.

Tip
The two dampeners should be installed close to each other on the exhaust pipe, but the dampeners should not touch together.

3. Install the two dampeners, P/N 10199232, starting at the mark on the exhaust pipe with the weights pointing up towards the underside of the pickup box.

1999-2000 2WD Models Built Prior to 1/00

These models will require the installation of a flex coupler, two Y-pipe support brace rods w/integral U-bolt clamp assemblies on the LH and RH sides of the transmission rear mount and new transmission mount studs and nuts. The Y-pipe support braces are used in combination with the flex coupler to reduce exhaust moan.

1. Install the flex coupler using steps 1-7 in the first procedure.
2. Support the transmission with a suitable adjustable jack stand.
3. Remove the two bolts and nuts from the transmission rear mount.
4. Position the transmission rear mount and install two new studs to the mount.
5. Install the new studs supplied with the kit to the transmission mount.



6. Loosely position the Y-pipe support braces w/integral U-bolt clamps (LH and RH) to the underside of the transmission rear mount and the crossover pipe as shown. The top ends of the braces attach to the underside of the transmission rear mount. The bottom ends of the braces attach to the crossover pipe using the integral U-bolt clamps. The braces support the LH leg of the Y-pipe where it crosses over the vehicle to meet the Y-pipe collector.
7. Install the two nuts to the transmission rear mount and the two nuts to the U-bolt clamps.

Tighten

•	Tighten the new transmission mount nuts to 25 N·m (18 lb ft).

•	Tighten the two U-bolt clamps to 30 N·m (22 lb ft).

8. Lower the vehicle.
9. Verify that the condition has been fixed.

If the exhaust vibration or moan is still present, order two exhaust dampeners, P/N 10199232, and proceed to Installation of Exhaust Dampeners, If Necessary in this bulletin.

For vehicles repaired under warranty, use: