Maintenance Schedule - Long Trip/Highway Gasoline
Perform the services shown in this schedule up to 166 000 km
(100,000 miles) and after 166 000 km (100,000 miles)
at the same intervals.
12 500 km (7,500 miles)
| • | Change the engine oil and the filter every 12 500 km (7,500 miles)
or every 12 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Verify the rear fluid level. Add fluid as needed. |
| • | Verify the constant velocity joints and the axle seals
for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension |
25 000 km (15,000 miles)
| • | Change the engine oil and the filter every 25 000 km (15,000 miles)
or every 12 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and the axle seals for leaks. |
| • | Inspect the shields and the underhood insulation (GVWR above 3 855 kg (8,500 lbs)). |
37 500 km (22,500 miles)
| • | Change the engine oil and the filter every 37 500 km (22,500 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and the axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
50 000 km (30,000 miles)
| • | Change the engine oil and the filter every 50 000 km (30,000 miles)
or every 12 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and the axle seals for leaks. |
| • | Clean and repack the front wheel bearings (or at each brake relining,
whichever occurs first). |
| • | Replace the air filter. |
| • | Replace the fuel filter. An Emission Control Service * |
| • | Inspect the shields and the underhood insulation. |
62 500 km (37,500 miles)
| • | Change the engine oil and the filter every 62 500 km (37,500 miles
) or every 12 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and the axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
75 000 km (45,000 miles)
| • | Change the engine oil and the filter every 75 000 km (45,000 miles)
or every 12 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and the axle seals for leaks. |
83 000 km (50,000 miles)
| • | Change the automatic transmission fluid and the filter if the
vehicle's GVWR is over 3 900 kg (8,600 lbs), or
if the vehicle is mainly driven under one or more of these conditions: |
| • | In heavy traffic where the outside temperature regularly reaches
32°C (90°F) or higher. |
| • | In hilly or mountainous terrain |
| • | When doing frequent trailer towing |
| • | Vehicles performing taxi, police or delivery services |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
87 500 km (52,500 miles)
| • | Change the engine oil and filter every 87 500 km (52,500 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
100 000 km (60,000 miles)
| • | Change the engine oil and filter every 100 000 km
(60,000 miles) or every 3 months, whichever occurs first. An Emission
Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and axle seals for leaks. |
| • | Clean and repack the front wheel bearings (or at each brake relining,
which ever occurs first). |
| • | Inspect the engine accessory drive belt. An Emission Control Service * |
| • | Replace the air filter. |
| • | Replace the fuel filter. An Emission Control Service * |
| • | Inspect the following components for damage or leaks. Replace
the parts as needed. An Emission Control Service * |
| • | If the engine has a thermostatically controlled cooling fan, inspect
all of the hoses and all of the ducts for proper hook-up. Ensure that the
valve works properly. |
| • | Conduct an Exhaust Gas Recirculation (EGR) system inspection. |
| • | Preform the following steps in order to conduct an evaporative
control system inspection: |
| 1. | Inspect all the fuel and vapor lines and hoses for proper hook-up,
routing and condition. |
| 2. | Ensure that the purge valve works properly (if equipped). |
| 3. | Replace the vapor lines, hoses, and the purge valve as needed. |
112 500 km (67,500 miles)
| • | Change the engine oil and the filter (or every 3 months,
whichever occurs first). An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
125 000 km (75,000 miles)
| • | Change the engine oil and filter (or every 3 months, whichever
occurs first). An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and axle seals for leaks. |
137 500 km (82,500 miles)
| • | Change the engine oil and filter (or every 3 months, whichever
occurs first). An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F)
or higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
150 000 km (90,000 miles)
| • | Change the engine oil and filter (or every 3 months, whichever
occurs first). An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and axle seals for leaks. |
| • | Clean and repack the front wheel bearings (or at each brake relining,
whichever occurs first). |
| • | Replace the air filter. |
| • | Replace the fuel filter. An Emission Control Service * |
162 500 km (97,500 miles)
| • | Change the engine oil and filter (or every 3 months, whichever
occurs first). An Emission Control Service * |
| • | Lubricate the following components. Do not lubricate the ball
joints unless the ball joint temperature is -12°C (10°F) or
higher. |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the constant velocity joints and axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
166 000 km (100,000 miles)
| • | Inspect the spark plug wires. |
| • | Replace the spark plug wires. An Emission Control Service * |
| • | Change the automatic transmission fluid and the filter. |
| • | Inspect the positive crankcase ventilation (PCV) valve. |
240 000 km (150,000 miles)
| • | Drain, flush and refill the cooling system (or every 60 months
since the last service, whichever comes first). Refer to Recommended Fluid
and Lubricants in this section. |
| • | Clean the following components. An Emission Control Service * |
Maintenance Schedule - Long Trip/Highway Diesel
Perform the services shown in this schedule up to 240 000 km
(150,000 miles) in this schedule and after 244 000 km
(150,000 miles) at the same intervals.
8 000 km (5,000 miles)
| • | Change the engine oil and the filter every 8 000 km (5,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate the ball joints unless their temperature is -12°C (10°F)
or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
16 000 km (10,000 miles)
| • | Change engine oil and filter every 16 000 km (10,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate the ball joints unless their temperature is -12°C (10°F)
or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components are tightly fitted. |
| • | Inspect the air cleaning housing in order to ensure that the air
cleaning housing is properly seated, the cover and wing nuts are tightly fitted. |
| • | Inspect the air cleaning housing in order to ensure that the air
cleaning housing cover and wing nuts are tightly fitted. |
| • | Tighten the connections and fasteners. Replace the necessary damaged
components. |
| • | Inspect the hoses and ducts for the proper maintenance if the
engine has a thermostatically controlled cooling fan. Verify that the valves
operate properly. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
24 000 km (15,000 miles)
| • | Change engine oil and filter at 24 000 km (15,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
32 000 km (20,000 miles)
| • | Change engine oil and filter every 32 000 km (20,000 miles)
or every three months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components are tightly fitted. |
| • | Inspect the air cleaning housing in order to ensure that the air
cleaning housing is properly seated, the cover and wing nuts are tightly fitted. |
| • | Inspect the air cleaning housing in order to ensure that the air
cleaning housing cover and wing nuts are tightly fitted. |
| • | Tighten the connections and fasteners. Replace the necessary damaged
components. |
| • | Inspect the hoses and ducts for the proper maintenance if the
engine has a thermostatically controlled cooling fan. Verify that the valves
operate properly. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
40 000 km (25,000 miles)
| • | Change engine oil and filter every 40 000 km (25,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
48 000 km (30,000 miles)
| • | Change engine oil and filter every 48 000 km (30,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Replace the air filters. An Emission Control Service * |
| • | Clean the front wheel bearings or each brake relining, whichever
occurs first. |
| • | Repack the front wheel bearings or each brake relining, whichever
occurs first. |
| • | Replace the oil filter. |
| • | Inspect the shields and underhood insulation for looseness. Adjust
or replace the shields and underhood insulation as required. |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components are tightly fitted. |
| • | Inspect the air cleaning housing in order to ensure that the air
cleaning housing is properly seated, the cover and wing nuts are tightly fitted. |
| • | Tighten the connections and fasteners. Replace the necessary damaged
components. |
| • | Inspect the hoses and ducts for the proper maintenance if the
engine has a thermostatically controlled cooling fan. Verify that the valves
operate properly. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
56 000 km (35,000 miles)
| • | Change engine oil and filter every 56 000 km (35,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
64 000 km (40,000 miles)
| • | Change engine oil and filter every 64 000 km (40,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components tightly fitted. |
| • | Inspect the air cleaning housing in order to ensure that the air
cleaning housing is properly seated, the cover and wing nuts are tightly fitted. |
| • | Tighten the connections and fasteners. Replace the necessary damaged
components. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
72 000 km (45,000 miles)
| • | Change engine oil and filter every 72 000 km (45,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
80 000 km (50,000 miles)
| • | Change engine oil and filter every 80 000 km (50,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F). |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Change the automatic transmission fluid and filter. 3 900 kg (8,600 lbs). |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components tightly fitted. |
| • | Inspect the air cleaning housing in order to ensure that the air
cleaning housing is properly seated, the cover and wing nuts are tightly fitted. |
| • | Tighten the connections and fasteners. Replace the necessary damaged
components. |
| • | Inspect the hoses and ducts for the proper maintenance if the
engine has a thermostatically controlled cooling fan. Verify that the valves
operate properly. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
88 000 km (55,000 miles)
| • | Change engine oil and filter every 88 000 km (55,000 miles)
or every three months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
96 000 km (60,000 miles)
| • | Change engine oil and filter every 96 000 km (60,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Replace the air filter. An Emission Control Service. * |
| • | Clean the front wheel bearings or each brake relining, or whichever
occurs first. |
| • | Repack the front wheel bearing or each brake relining, or whichever
occurs first. |
| • | Inspect the crankcase depression regulator valve system for the
following faulty conditions. This is also an Emission Control Service. * |
| • | Replace the fuel filter. |
| • | Inspect the equipped EGR System except for Code F engine. An Emission
Control Service. |
| • | Inspect the shields and the underhood insulation for looseness.
Adjust or replace the shields and the underhood insulation if damaged or loosed. |
| • | Change the automatic transmission fluid and filter if the vehicle's
GVWR exceeds 3 900 kg (8,600 lbs). |
| • | Change the automatic transmission fluid and filter if the vehicle
is mainly driven under one or more of the following conditions. |
| - | In heavy traffic with outdoor temperatures exceeding 32°C (90°F)
or higher. |
| - | In hilly and mountainous terrain |
| - | For frequent trailer towing |
| - | Uses found in the following services |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components tightly fitted. |
| • | Inspect the air cleaning housing in order to ensure that the air
cleaning housing is properly seated, the cover and wing nuts are tightly fitted. |
| • | Tighten the connections and fasteners. Replace the necessary damaged
components. |
| • | Inspect the hoses and ducts for the proper maintenance if the
engine has a thermostatically controlled cooling fan. Verify that the valves
operate properly. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components tightly fitted. |
| • | Inspect the air cleaning housing in order to ensure that the air
cleaning housing is properly seated, the cover and wing nuts are tightly fitted. |
| • | Tighten the connections and fasteners. Replace the necessary damaged
components. |
| • | Inspect the hoses and ducts for the proper maintenance if the
engine has a thermostatically controlled cooling fan. Verify that the valves
operate properly. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
104 000 km (65,000 miles)
| • | Change engine oil and filter every 104 000 km (65,000 miles)
or every three months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
112 000 km (70,000 miles)
| • | Change engine oil and filter every 112 000 km (70,000 miles)
or every three months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components tightly fitted. |
| • | Inspect the hoses and ducts for the proper maintenance if the
engine has a thermostatically controlled cooling fan. Verify that the valve
operate properly. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
120 000 km (75,000 miles)
| • | Change engine oil and filter every 120 000 km (75,000 miles)
or every three months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
128 000 km (80,000 miles)
| • | Change engine oil and filter every 128 000 km (80,000 miles)
or every three months, or whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components tightly fitted. |
| • | Inspect the hoses and ducts for the proper maintenance if the
engine has a thermostatically controlled cooling fan. Verify that the valves
operate properly. |
| • | Rotate the tires. Refer to Tire Rotation
in Suspension. |
136 000 km (85,000 miles)
| • | Change engine oil and filter every 136 000 km (85,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F). |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
144 000 km (90,000 miles)
| • | Change engine oil and filter every 144,000 km (90,000 miles)
or every 3 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Replace the air filter. An Emission Control Service. |
| • | Clean the front wheel bearings or each brake relining, or whichever
occurs first. |
| • | Repack the front wheel bearing or each brake relining, or whichever
occurs first. |
| • | Replace the fuel filter. |
| • | Inspect the shields and underhood insulation for looseness. Adjust
the shields and underhood insulation as required. |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components tightly fitted. |
| • | Inspect the hoses and ducts for the proper maintenance if the
engine has a thermostatically controlled cooling fan. Verify that the valves
operate properly. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
152 000 km (95,000 miles)
| • | Change engine oil and filter every 152 000 km (95,000 miles)
or every three months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
160 000 km (100,000 miles)
| • | Change engine oil and filter every 160 000 km (100,000 miles)
or every 60 months, whichever occurs first. An Emission Control Service * |
| • | Lubricate the following vehicle components when performing a maintenance
schedule: |
| - | The transmission shift linkage |
| - | The park brake cable guides |
| - | The brake pedal springs |
| • | Do not lubricate ball joints unless the ball joint temperature
exceeds -12°C (10°F) or higher. |
| • | Inspect the rear fluid level. Add fluid as needed. |
| • | Inspect the axle seals for leaks. |
| • | Drain, flush and refill the cooling system with coolant. |
| • | Inspect the hoses if the hoses are cracked, swollen, or deteriorated.
Replace the hoses if damaged. Tighten the hose clamps except for the constant
tension clamps. Remove and clean the debris out the radiator and the air
conditioning condenser. Clean the radiator neck thoroughly in order to ensure
proper operation. Pressure test the radiator and the cap. |
| • | Change the automatic transmission fluid and filter. |
| • | Inspect the shields and underhood insulation for looseness. Adjust
the shields and underhood insulation as required. |
| • | Inspect the air intake system installation in order to ensure
that the gaskets are properly sealed. |
| • | Inspect the air intake system installation in order to ensure
that hose connections, fasteners and other components tightly fitted. |
| • | Inspect hoses and ducts for the proper maintenance if the engine
has a thermostatically controlled cooling fan. Ensure that the valve operates
properly. |
| • | Rotate the tire. Refer to Tire Rotation
in Suspension. |
240 000 km (150,000 miles)
| • | Drain, flush and refill the cooling system every 240 000 km (150,000 miles
) or every 60 months, whatever exceeds first. Refer to Recommended
Fluid and Lubricants. Inspect the hoses. Clean the radiator, condenser, pressure
cap and neck. An Emission Control Service * |
| • | Change the automatic transmission fluid and filter. |
