GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The On-Board Diagnostic (OBD) System Check is an organized approach to identifying a problem created by a control module system malfunction. The OBD is the starting point for any driveability concern diagnosis. The OBD directs the service technician to the next logical step in diagnosing the concern.

Perform this check only if there is a driveability complaint or if you have been sent to this system check from another section in the service information.

Understanding the table properly reduces the diagnostic time. Proper use of the OBD helps prevent the unnecessary replacement of good parts.

Diagnostic Aids

Important: Do not clear the DTCs unless directed by a diagnostic procedure. Clearing the DTCs will also clear valuable Freeze Frame and Failure Records data.

Inspect all related wiring and connections including the connections at the VCM. These may cause an intermittent condition.

Any base engine problem could alter scan tool data. Examples of these are: distributor timing, valve timing, and intake gasket leaks.

An intermittent may be caused by any of the following conditions:

    • A poor connection
    • Rubbed through wire insulation
    • A broken wire inside the insulation

Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.

If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.

Test Description

The numbers below refer to the step numbers in the diagnostic table.

  1. . This step determines if the scan tool powers up when connected to the DLC.

  2. The MIL should be ON when the ignition is turned ON.

  3. Refer to DTC List (Definitions) for a list of valid DTCs.

  4. Refer to Data Link Connector (DLC) Schematics in Wiring Systems to determine all of the modules communicating on the Class 2 Serial Data circuit. If any of the modules are not present in the Diagnostic Circuit Check, then the module(s) never established communications. The scan tool will indicate a YES state for communicating modules and a NO state for modules that had established, yet no longer communicate.

  5. If the vehicle does not start or starts and stalls, the Passlock system could be the cause.

  6. This test determines if the MIL can be controlled by the VCM.

  7. Comparing the ACTUAL and TYPICAL scan tool data values will aid in determining if the engine parameter is within limits (i.e., Advanced timing can substantially alter sensor values.)

Step

Action

Value(s)

Yes

No

1

Important: Check for applicable service bulletins before proceeding with this test.

Perform this test only if there is a driveability complaint or if you have been sent to this table from another section in the service information.

Important: Do not turn the ignition OFF when performing this diagnostic. Do NOT clear DTCs unless instructed by this diagnostic. Turn ON the ignition leaving the engine OFF.

Does the scan tool power up?

--

Go to Step 2

Go to Data Link Connector Diagnosis

2

Turn ON the ignition leaving the engine OFF.

Is the MIL ON?

--

Go to Step 3

Go to Malfunction Indicator Lamp Circuit Check

3

Attempt to establish communications with VCM.

Does the scan tool communicate with the VCM?

--

Go to Step 4

Go to Data Link Connector Diagnosis

4

Save the DTC Freeze Frame and the Failure Records if any of the following DTC status are set in the scan tool DTC Information:

  1. Last Test Failed
  2. Test Failed This Ignition
  3. MIL Request
  4. History DTC

Did you find any DTCs?

--

Go to the applicable DTC table

Go to Step 5

5

Monitor the Serial Data Class 2 message with the scan tool.

Are all other modules communicating with the scan tool?

--

Go to Step 6

Go to Data Link Connector Diagnosis

6

Attempt to start the engine.

Does the engine start and continue to run?

--

Go to Step 8

Go to Step 7

7

Check for any Passlock DTCs in Body and Chassis.

Were any DTCs found?

--

Go to the applicable DTC table.

Go to Engine Cranks but Does Not Run

8

Command the MIL OFF with the scan tool.

Does the MIL turn OFF?

--

Go to Step 9

Go to Malfunction Indicator Lamp Circuit Check

9

Compare the scan tool engine data with the TYPICAL scan tool values.

Are the values within typical ranges?

--

Go to Symptoms

Go to Diagnostic Aids