Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category |
DTC Descriptor
DTC P0030: O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)DTC P0031: O2 Sensor Heater Circuit Low Voltage (Bank 1 Sensor 1)
DTC P0032: O2 Sensor Heater Circuit High Voltage (Bank 1 Sensor 1)
DTC P0036: O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
DTC P0037: O2 Sensor Heater Circuit Low Voltage (Bank 1 Sensor 2)
DTC P0038: O2 Sensor Heater Circuit High Voltage (Bank 1 Sensor 2)
DTC P0050: O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
DTC P0051: O2 Sensor Heater Circuit Low Voltage (Bank 2 Sensor 1)
DTC P0052: O2 Sensor Heater Circuit High Voltage (Bank 2 Sensor 1)
DTC P0056: O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
DTC P0057: O2 Sensor Heater Circuit Low Voltage (Bank 2 Sensor 2)
DTC P0058: O2 Sensor Heater Circuit High Voltage (Bank 2 Sensor 2)
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Ignition Voltage | P0030, P0036, P0050, P0056 | P0030, P0036, P0050, P0056 | -- | P0135, P0141, P0155, P0161 |
HO2S Heater Control Sensor 1 Bank 1 or 2 | P0031, P0051 | P0030, P0050 | P0032, P0052 | P0135, P0141, P0155, P0161 |
HO2S Heater Control Sensor 2 Bank 1 or 2 | P0037, P0057 | P0036, P0056 | P0038, P0058 | P0135, P0141, P0155, P0161 |
Circuit Description
The heated oxygen sensor (HO2S) heater reduces the time required for the oxygen sensor to reach operating temperature and maintains the operating temperature during extended idle periods. When the ignition is turned to the Run position, ignition voltage is supplied directly to the sensor heater. The engine control module (ECM) controls the heater operation by first modulating the control circuit to ground when the sensors are cold. This prevents the possibility of thermal shock to the sensor from condensation build-up on the sensor, by controlling the sensors rate of heating. After a predetermined amount of time the ECM commands the heaters ON continuously. Once the sensor reaches operating temperature the ECM may modulate the heater control circuit to ground, to maintain a desired temperature.
The ECM controls the heater by grounding the control circuit with a solid state device called a driver. The driver is equipped with a feedback circuit that is pulled-up to voltage. The ECM can determine if the control circuit is open, shorted to ground or shorted to a voltage by monitoring the feedback voltage.
Conditions for Running the DTC
P0030, P0031, P0032, P0050, P0051, P0052
| • | The ignition voltage is between 10-18 volts. |
| • | The engine speed is greater than 80 RPM. |
| • | The HO2S heater is commanded ON and OFF at least once during the ignition cycle. |
| • | The DTCs run continuously once the above conditions are met for 1 second. |
P0036, P0037, P0038, P0056, P0057, P0058
| • | The ignition voltage is between 10-18 volts. |
| • | The engine speed is greater than 80 RPM. |
| • | The HO2S heater is commanded ON and OFF at least once during the ignition cycle. |
| • | The secondary HO2S is at operating temperature. |
| • | The DTCs run continuously once the above conditions are met for 1 second. |
Conditions for Setting the DTC
P0030, P0036, P0050, P0056
The ECM detects an open circuit in the heater circuits of the HO2S when the heater is commanded OFF. The condition exists for greater than 4 seconds or a cumulative of 30 seconds.
P0031, P0037, P0051, P0057
The ECM detects a ground in the heater circuits of the HO2S when the heater is commanded OFF. The condition exists for greater than 4 seconds or a cumulative of 30 seconds.
P0032, P0038, P0052, P0058
The ECM detects a short to voltage in the heater circuits of the HO2S when the heater is commanded ON. The condition exists for greater than 4 seconds or a cumulative of 30 seconds.
Action Taken When the DTC Sets
DTCs P0030, P0031, P0032, P0036, P0037, P0038, P0050, P0051, P0052, P0056, P0057 and P0058 are type B DTCs.
Conditions for Clearing the MIL/DTC
DTCs P0030, P0031, P0032, P0036, P0037, P0038, P0050, P0051, P0052, P0056, P0057 and P0058 are type B DTCs.
Diagnostic Aids
| • | If the condition is intermittent, move the related harnesses and connectors with the engine operating, while monitoring the circuit status for the component with a scan tool. If the circuit status parameter changes from OK or Indeterminate to Fault there is a condition with the circuit or a connection. |
| • | An open fuse in the HO2S heater circuit may be caused by the heater element in one of the sensors. The condition may not be present until the sensor operates for a period of time. If no fault is present in the heater circuit, monitor the amperage of each heater using the DMM to determine if one of the heater elements is the cause of the open fuse. Inspect the sensor pigtail or the harness for contacting the exhaust system. |
Reference Information
Schematic Reference
Connector End View Reference
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Engine idling at operating temperature for at least 30 seconds. Observe the DTC information, DTCs P0030, P0031, P0032, P0036, P0037, P0038, P0050, P0051, P0052, P0056, P0057 and P0058 should not set.
- Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the appropriate heated oxygen sensor (HO2S).
- Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 and ground.
- Connect a test lamp between the heater control circuit terminal 2 and B+. The test lamp should not illuminate.
- Idle the engine, and verify the test lamp illuminates or flashes.
- Ignition ON, test for 2.0-3.0 V between the control circuit terminal 2 and ground.
- If all circuits/connections test normal, test or replace the HO2S sensor.
Note: The ignition circuit supplies voltage to other components. Make sure you test all circuits for a short to ground or test all components for being shorted that share the ignition circuit.
| ⇒ | If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition circuit fuse is open, test all the components connected to the ignition circuit and replace as necessary. |
| ⇒ | If the test lamp is always ON, test the control circuit for a short to ground. If the circuit/connections test normal, replace the ECM. |
Note: The control circuit for the HO2S heater is pulled-up to voltage within the ECM, 2.0-3.0 V on the control circuit is normal.
| ⇒ | If the test lamp is always OFF, test the control circuit terminal 2 for an open/high resistance. If the circuit/connections test normal, replace the ECM. |
| ⇒ | If not within the specified range, test the control circuit for a short to voltage. If the circuit/connections test normal, replace the ECM. |
Component Testing
- Ignition OFF, disconnect the harness connector at the heated oxygen sensor (HO2S) sensor.
- Test for 5-25 Ω between the control terminal 2 and the ignition terminal 1 of the heated oxygen sensor (HO2S) sensor.
| ⇒ | If not within the specified range, replace the HO2S sensor. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Engine Control Module Replacement for engine control module replacement, setup, and programming |
