The Keyless Entry Scan Tool Data List contains all of the keyless entry related parameters that are available on the scan tool. Use the Keyless Entry Scan Tool Data List as directed by a diagnostic table or in order to supplement the diagnostic procedures. Begin all of the diagnostic procedures with Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle.
Use the Scan Tool Data List only after the following is determined:
| • | There is no published DTC procedure nor published symptom procedure for the customer concern. |
| • | The DTC or symptom diagnostic procedure indicated by the diagnostic system check does not resolve the customer concern. |
The Typical Data Values are obtained from a properly operating vehicle under the conditions specified in the first row of the Scan Tool Data List table. Comparison of the parameter values from the suspect vehicle with the Typical Data Values may reveal the source of the customer concern.
Parameter | Operating Conditions | Expected Value | Definition |
|---|---|---|---|
Ignition is ON, engine OFF, and vehicle is stationary | |||
Last Remote Key Used | -- | None | The scan tool displays None or Key No. This is the last remote key used as monitored by the RFA. |
-- | Key No. | ||
Remote Key N[ordm ] 1 | -- | Programmed | The scan tool displays Programmed or Reprogram. Programmed is displayed if Key N[ordm ] 1 is programmed into the RFA. |
-- | Reprogram | ||
Remote Key 1 Function | -- | None | The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, Locate. This is the state of the Key N[ordm ] 1 command as monitored by the RFA. |
Remote key door lock button pressed | Lock | ||
Remote key door unlock button pressed | Dr. door unlock | ||
Remote key door unlock button pressed twice | All door unlock | ||
Remote key locate button pressed | Locate | ||
Battery Status Remote Key 1 | Normal battery status in remote key 1 | OK | The scan tool displays OK or Low. This is the state of the Key 1 battery. |
Low battery status in remote key 1 | Low | ||
Remote Key N[ordm ] 2 | -- | Programmed | The scan tool displays Programmed or Reprogram. Programmed is displayed if Key N[ordm ] 2 is programmed into the RFA. |
-- | Reprogram | ||
Remote Key 2 Function | -- | None | The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, Locate. This is the state of the Key N[ordm ] 2 command as monitored by the RFA. |
Remote key door lock button pressed | Lock | ||
Remote key door unlock button pressed | Dr. door unlock | ||
Remote key door unlock button pressed twice | All door unlock | ||
Remote key locate button pressed | Locate | ||
Battery Status Remote Key 2 | Normal battery status in remote key 1 | OK | The scan tool displays OK or Low. This is the state of the Key 2 battery. |
Low battery status in remote key 1 | Low | ||
Remote Key N[ordm ] 3 | -- | Programmed | The scan tool displays Programmed or Reprogram. Programmed is displayed if Key N[ordm ] 3 is programmed into the RFA. |
-- | Reprogram | ||
Remote Key 3 Function | -- | None | The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, Locate. This is the state of the Key N[ordm ] 3 command as monitored by the RFA. |
Remote key door lock button pressed | Lock | ||
Remote key door unlock button pressed | Dr. door unlock | ||
Remote key door unlock button pressed twice | All door unlock | ||
Remote key locate button pressed | Locate | ||
Battery Status Remote Key 3 | Normal battery status in remote key 1 | OK | The scan tool displays OK or Low. This is the state of the Key 3 battery. |
Low battery status in remote key 1 | Low | ||
Remote Key N[ordm ] 4 | -- | Programmed | The scan tool displays Programmed or Reprogram. Programmed is displayed if Key N[ordm ] 4 is programmed into the RFA. |
-- | Reprogram | ||
Remote Key 4 Function | -- | None | The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, Locate. This is the state of the Key N[ordm ] 4 command as monitored by the RFA. |
Remote key door lock button pressed | Lock | ||
Remote key door unlock button pressed | Dr. door unlock | ||
Remote key door unlock button pressed twice | All door unlock | ||
Remote key locate button pressed | Locate | ||
Battery Status Remote Key 4 | Normal battery status in remote key 1 | OK | The scan tool displays OK or Low. This is the state of the Key 4 battery. |
Low battery status in remote key 1 | Low | ||
Scan Tool Output Control | Additional Menu Selections | Description |
|---|---|---|
Tyre Pressure Monitor (TPM) Option | TPM Option Enable | After replacing the remote control door lock receiver (RCDLR), the scan tool must be used to enable the TPM option, refer to Control Module References After the TPM option is enabled, it can not be disabled. |
Vehicle Tyre Type and Tyre Pressure | Tyre Type/Pressure Selection | After replacing the RCDLR, the scan tool must be used to select the correct tyre type and the front and rear tyre pressures for the vehicle, refer to Control Module References |
Parameter | Operating Conditions | Expected Value | Definition |
|---|---|---|---|
Ignition is ON, engine OFF, and vehicle is stationary | |||
Learn in Progress | - | On | The scan tool displays On/Off. On indicates the tyre pressure monitor (TPM) system is in sensor learn mode. Off indicates the TPM system is not in the sensor learn mode. |
- | Off | ||
Left Front Tyre Pressure | - | 1020 kpa | The scan tool displays 0-290 kPa (0-42 psi). The actual pressure of the left front tyre. |
Left Rear Tyre Pressure | - | 1020 kpa | The scan tool displays 0-290 kPa (0-42 psi). The actual pressure of the left front tyre. |
LF TPS (left front tyre pressure) | - | Learned | |
LF TPS Battery Status | - | Okay | This parameter displays the status of the left front tyre pressure sensor battery. |
- | Low | ||
LF TPS Counter (left front tyre pressure) | - | 0 | |
LF TPS Fault (Left Front) | - | Yes | This parameter displays whether there is a fault with the left front tyre pressure sensor. |
- | No | ||
LF TPS ID (left front tyre pressure) | - | 406606 | A number displayed indicates the left front tyre pressure sensors unique identification (ID) code and that it has been learned into the antenna modules memory. |
LF TPS Mode (left front tyre pressure) | - | Learn mode LF | This data parameter indicates the mode contained in the last transmission received from the left front tyre pressure sensor. |
LF TPS Signal Strength | - | 0 | This parameter displays the strength of the signal from the left front tyre pressure sensor. |
LF Tyre High Pressure Threshold | - | 376 kpa | |
LF Tyre Low Pressure Threshold | - | 200 kpa | |
LF Tyre Max. Low Pressure | - | 56 kpa | |
LF Tyre Pressure Status | - | Normal | The scan tool displays Normal or Failed. Normal indicates that the left front tyre pressure sensor has been learned. Failed indicates that the sensor has not been learned, or that it is not transmitting a valid ID code. |
- | Failed | ||
LR TPS (left rear tyre pressure) | - | Learned | |
LR TPS Battery Status | - | Okay | This parameter displays the status of the left rear tyre pressure sensor battery. |
- | Low | ||
LR TPS Counter | - | 0 | |
LR TPS Fault (left Rear) | - | Yes | This parameter displays whether there is a fault with the left rear tyre pressure sensor. |
- | No | ||
LR TPS ID | - | 406595 | A number displayed indicates the left rear tyre pressure sensors unique identification (ID) code and that it has been learned into the antenna modules memory. |
LR TPS Mode (left rear tyre pressure) | - | Learn mode LF | This data parameter indicates the mode contained in the last transmission received from the left rear tyre pressure sensor. |
LR TPS Signal Strength | - | 0 | This parameter displays the strength of the signal from the left rear tyre pressure sensor. |
LR Tyre High pressure Threshold | - | 376 kpa | |
LR Tyre Low Pressure Threshold | - | 200 kpa | |
LR Tyre Max. Low Pressure | - | 56 kpa | |
LR Tyre Pressure Status | - | Normal | The scan tool displays Normal or Failed. Normal indicates that the left rear tyre pressure sensor has been learned. Failed indicates that the sensor has not been learned, or that it is not transmitting a valid ID code. |
- | Failed | ||
RF TPS (right front tyre pressure) | - | Learned | |
RF TPS Battery Status | - | Okay | This parameter displays the status of the right front tyre pressure sensor battery. |
- | Low | ||
RF TPS Counter | - | 0 | |
RF TPS Fault (right front) | - | Yes | This parameter displays whether there is a fault with the right front tyre pressure sensor. |
- | No | ||
RF TPS ID | - | 406582 | A number displayed indicates the right front tyre pressure sensors unique identification (ID) code and that it has been learned into the antenna modules memory. |
RF TPS Mode (right front tyre pressure) | - | Learn mode LF | This data parameter indicates the mode contained in the last transmission received from the right front tyre pressure sensor. |
RF TPS Signal Strength | - | 0 | This parameter displays the strength of the signal from the right front tyre pressure sensor. |
RF tyre High Pressure Threshold | - | 376 kpa | |
RF Tyre Low Pressure Threshold | - | 200 kpa | |
RF Tyre Max. Low Pressure | - | 56 kpa | |
RF Tyre Pressure Status | - | Normal | The scan tool displays Normal or Failed. Normal indicates that the right front tyre pressure sensor has been learned. Failed indicates that the sensor has not been learned, or that it is not transmitting a valid ID code. |
- | Failed | ||
Right Front Tyre Pressure | - | 1020 kpa | The scan tool displays 0-290 kPa (0-42 psi). The actual pressure of the left front tyre. |
Right Rear Tyre Pressure | - | 1020 kpa | The scan tool displays 0-290 kPa (0-42 psi). The actual pressure of the left front tyre. |
RR TPS (right rear tyre pressure) | - | Learned | |
RR TPS Battery Status | - | Okay | This parameter displays the status of the right rear tyre pressure sensor battery. |
- | Low | ||
RR TPS Counter | - | 0 | |
RR TPS Fault (Right Rear) | - | Yes | This parameter displays whether there is a fault with the right rear tyre pressure sensor. |
- | No | ||
RR TPS ID | - | 406615 | A number displayed indicates the right rear tyre pressure sensors unique identification (ID) code and that it has been learned into the antenna modules memory. |
RR TPS Mode (right rear tyre pressure) | - | Learn mode LF | This data parameter indicates the mode contained in the last transmission received from the right rear tyre pressure sensor. |
RR TPS Signal Strength | - | 0 | This parameter displays the strength of the signal from the right rear tyre pressure sensor. |
RR Tyre High Pressure Threshold | - | 376 kpa | |
RR Tyre Low Pressure Threshold | - | 200 kpa | |
RR Tyre Max. Low Pressure | - | 56 kpa | |
RR Tyre Pressure Status | - | Normal | The scan tool displays Normal or Failed. Normal indicates that the right rear tyre pressure sensor has been learned. Failed indicates that the sensor has not been learned, or that it is not transmitting a valid ID code. |
- | Failed | ||
Tyre Pressure Indicator Request | - | Active | |
- | Inactive | ||
Vehicle Speed | -- | 0km | The scan tool range is 0-255 km/h (0-158 mph). This parameter indicates the vehicle speed calculated by the ECM from the vehicle speed sensor (VSS). |
