GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The fuel level sender changes resistance based on fuel level. The powertrain control module (PCM) monitors the signal circuit of the fuel level sender in order to determine fuel level. When the fuel tank is full, the sender resistance is high and the PCM senses a high signal voltage. When the fuel tank is empty, the sender resistance is low and the PCM senses a low signal voltage. The PCM uses the signal circuit of the fuel level sender in order to calculate the total remaining fuel percentage in the tank. The PCM sends the fuel level percent via the class 2 serial data circuit to the instrument cluster in order to control the fuel gage. The fuel level information is also used for misfire and evaporative emission (EVAP) diagnostics.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0462 Fuel Level Sensor Circuit Low Voltage

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

    • The fuel level signal is less than 1 percent.
    • The above condition is present for greater than 20 seconds.

Action Taken When the DTC Sets

    • The fuel gage defaults to empty.
    • The LOW FUEL indicator illuminates.
    • The PCM records the operating conditions at the time the diagnostic fails. The PCM displays the failure information in the Failure Records on the scan tool.

Conditions for Clearing the DTC

    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The history DTC clears after 40 malfunction free warm-up cycles.
    • The PCM receives the clear code command from the scan tool.

Diagnostic Aids

    • Use the Freeze Frame and/or Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data may aid in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also aid in determining the number of ignition cycles that the diagnostic reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions such as RPM, engine load, vehicle speed, temperature, etc. This will isolate when the DTC failed.
    • Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The number below refers to the step number on the diagnostic table.

  1. Tests for the proper operation of the circuit in the high voltage range.

Step

Action

Values

Yes

No

Schematic Reference: Instrument Cluster Schematics

Connector End View Reference: Master Electrical Component List

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. With a scan tool, observe the Fuel Tank Level Remaining parameter in the powertrain control module (PCM) Enhanced evaporative emission (EVAP) Data, data list.

Does the scan tool indicate that the Fuel Tank Level Remaining parameter is less than the specified value?

1%

Go to Step 3

Go to Diagnostic Aids

3

  1. Turn the ignition OFF.
  2. Disconnect C104.
  3. Turn the ignition ON, with the engine OFF.
  4. With a scan tool, observe the Fuel Tank Level Remaining parameter.

Does the scan tool indicate that the Fuel Tank Level Remaining parameter is greater than the specified value?

99%

Go to Step 5

Go to Step 4

4

Test the signal circuit of the fuel level sender for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 7

5

Test the signal circuit of the fuel level sender for a short to ground between C104 and the fuel level sender. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 6

6

Inspect for poor connections at the harness connector of the fuel level sender. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 8

7

Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 9

8

Replace the fuel level sender. Refer to Fuel Level Sensor Replacement in Engine Controls - 4.3L .

Did you complete the replacement?

--

Go to Step 10

--

9

Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 10

--

10

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC.

Does the DTC reset?

--

Go to Step 2

System OK