Tools Required

1. Attach the J 45759 to the transfer case using the adapter studs. All of the transfer case disassembly procedures can be performed with the case mounted to the J 45759 .



2. Mount the J 3289-20  (1) to a sturdy workbench.
3. Install the J 45759  (2) into J 3289-20  (1) and secure with pivot pin.



4. Remove the fill plug (1) and the drain plug (2) and drain the transfer case fluid.



5. Remove the actuator encoder motor mounting bolts.
6. Remove the actuator encoder motor assembly.
7. Remove the actuator insulator gasket.



8. Remove the vent and the seal, only if damaged.



9. Remove the rear vehicle speed sensors (VSS).



10. Remove the front VSS.



11. Remove the access hole plug.



12. Remove the front output shaft dust seal.

Notice: Refer to Transfer Case Seal Removal Notice in the Preface section.




13. Remove the front output shaft seal.

Notice: Refer to Transfer Case Seal Removal Notice in the Preface section.




14. Remove the input shaft seal by prying it out of the front case.



15. Remove the rear output shaft seal.



16. Inspect the rear output shaft bushing for scoring or wear.
17. Remove the rear output shaft bushing using the J 45380 .

17.1.

Install the finger section of the J 45380 in front of the bushing.

17.2.

Install the tube and forcing screw assembly to the finger section. Ensure the forcing screw is backed out.

17.3.

Using a wrench on the forcing screw, remove the rear output shaft bushing.





Important: The magnesium transfer cases are using new style bolts that have a cup style washer. The cup washer is only available with the bolt. If the cup washer is not damaged, the bolt can be used again.

18. Remove the transfer case retaining bolts and washers.

Mark the location of any brackets.

Notice: Refer to Machined Surface Damage Notice in the Preface section.




19. Insert a flat-blade screwdriver into the slot on the left side of the transfer case.



20. Insert a flat-blade screwdriver into the slot on the right side of the transfer case.
21. With equal pressure, press down on the screwdrivers in order to separate the front case half and the rear case half.



22. Insert a pair of snap ring pliers and release the outer retaining ring for the rear output shaft bearing.



23. Remove the rear case half from the front case half.



24. Remove the oil pump wear sleeve, only if it is worn or damaged.



25. Remove the rear output shaft rear bearing retaining ring.



26. Remove the rear output shaft rear bearing.



27. Remove the rear output shaft speed sensor reluctor wheel.



28. Remove the magnet.



29. Remove the oil pump suction pipe assembly. Do not remove the screen from the pipe.



30. Remove the oil pump assembly.



31. Remove the oil pump suction pipe O-ring from the oil pump.



32. Remove the drive sprocket retaining ring.



33. Remove the driven sprocket retaining ring.




Important: If the chain and sprockets are to be used again, mark the relationship of the chain to the sprockets in order to mark the wear patterns.

34. Remove the chain and sprockets.
35. Remove the chain from the drive sprocket and driven sprocket.



36. Remove the rear output shaft assembly.
37. Mount the rear output shaft assembly in a soft-jaw vise with the input end up.



38. Remove the clutch assembly retaining ring. Push down on the clutch pressure plate to access the retaining ring.



39. Remove the clutch pressure plate assembly.
40. Remove the clutch pressure plate spring.



41. Remove the clutch pressure plate bearing, with the clutch bearing inner support, from the clutch pressure plate.



42. Inspect the bearing for being faulty. Refer to Transfer Case Cleaning and Inspection .
43. If the bearing is faulty, using a hydraulic press and a suitable adapter, remove the clutch pressure plate bearing from the clutch bearing inner support.
44. Discard the bearing after removal.



45. Remove the clutch hub retaining ring.
46. Remove the clutch housing and hub assembly from the rear output shaft.



47. Turn the clutch assembly over on a workbench.

Important: Do not remove the oil restrictor plate. The oil restrictor plate is only serviced with the clutch hub.

48. Remove the clutch hub.
49. Remove the clutch housing.




Important: Do not wash the clutch inner friction plates in cleaning solvent.

50. Separate the clutch plates for inspection.
51. Remove and discard the shim or shims.



52. Remove the oil restrictor from the rear output shaft, if replacing the shaft.



53. Inspect the bearing in the clutch housing for being faulty. Refer to Transfer Case Cleaning and Inspection .
54. If the bearing is faulty, use a brass drift and a hammer to remove the bearing.



55. Remove both of the clutch lever pivot pins along with the aluminum washers and O-ring seals.



56. Remove the shift detent spring bolt.
57. Remove the following components:

•	The shift detent plunger plug O-ring seal

•	The shift detent spring

•	The shift detent plunger




58. Remove the clutch lever assembly.



59. Remove the shift fork shaft.



60. Remove the range shift fork and the range shift sleeve as an assembly.

It may be necessary to pry the roller on the shift fork from the control actuator lever.




61. Remove the range shift sleeve from the range shift fork.



62. Remove the outer retaining ring for the input gear bearing.



63. Remove the high/low planetary carrier.



64. Remove the front output shaft bearing retaining ring.



65. Remove the front output shaft assembly.



66. If damaged, remove the speed sensor reluctor wheel from the front output shaft using a hydraulic press.

Do not use the speed sensor reluctor wheel again after removal.




67. Remove the planetary gear shaft retaining ring.



68. Remove the carrier lock plate.



69. Remove the input shaft thrust washer.



70. Remove the input gear from the planetary carrier.



71. Remove the thrust washer.



72. Inspect the pilot bearing in the input gear for being faulty. Refer to Transfer Case Cleaning and Inspection .
73. Remove the pilot bearing from the input gear using a brass drift and a hammer.



74. Remove the input bearing retaining ring.



75. Remove the input bearing.



76. Remove the front output shaft front bearing retainer ring.
77. Remove the front output shaft front bearing.



78. Inspect the front output shaft rear bearing for being faulty. Refer to Transfer Case Cleaning and Inspection .
79. If the bearing is faulty, remove the bearing using the J 23907  (2) and the J 26941  (1).



80. Remove the retaining ring for the control actuator lever shaft.



81. Remove the control actuator lever shaft.
82. Inspect the control actuator lever bearing and seal for being faulty. Refer to Transfer Case Cleaning and Inspection .
83. If the bearing is leaking or faulty, remove the bearing from the case.



84. Remove the mounting studs, only if they are damaged.