Drivetrain and Front Suspension Frame Insulator Replacement Regular Cab

Properly support the frame when you change the frame cushions. If only one cushion is changed, lower the entire side on which the cushion in placed in order to provide clearance for the cushion.

1. Raise the vehicle slightly on a hoist. Refer to Lifting and Jacking the Vehicle in General Information.



2. Place jack stands under the body on the side of the vehicle that the cushions will be placed.



3. Remove the frame cushion bolts.
4. Remove the retainer.
5. Remove the lower cushion.
6. Lower the hoist enough in order to leave the body supported by the jack stands.
7. Remove the upper cushion.
8. Remove the shims, if equipped.

1. Install the shims, if equipped.
2. Install the upper cushion.
3. Raise the frame slightly on the hoist.
4. Install the lower cushion.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the frame cushion bolts.

Tighten
Tighten the bolts to 70 N·m (52 lb ft).

6. Lower the hoist.

Drivetrain and Front Suspension Frame Insulator Replacement Extended Cab

Properly support the frame when you change the frame cushions. If only one cushion is changed, lower the entire side on which the cushion in placed in order to provide clearance for the cushion.

1. Raise the vehicle slightly on a hoist. Refer to Lifting and Jacking the Vehicle in General Information.



2. Place jack stands under the body on the side of the vehicle that the cushions will be placed.



3. Remove the frame cushion bolts.
4. Remove the retainer.
5. Remove the lower cushion.
6. Lower the hoist enough in order to leave the body supported by the jack stands.
7. Remove the upper cushion.
8. Remove the shims, if equipped.

1. Install the shims, if equipped.
2. Install the upper cushion.
3. Raise the frame slightly on the hoist.
4. Install the lower cushion.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the frame cushion bolts.

Tighten
Tighten the bolts to 70 N·m (52 lb ft).

6. Lower the hoist.

Drivetrain and Front Suspension Frame Insulator Replacement 2-Door Utility

Properly support the frame when you change the frame cushions. If only one cushion is changed, lower the entire side on which the cushion in placed in order to provide clearance for the cushion.

1. Raise the vehicle slightly on a hoist. Refer to Lifting and Jacking the Vehicle in General Information.



2. Place jack stands under the body on the side of the vehicle that the cushions will be placed.



3. Remove the frame cushion bolts.
4. Remove the retainer.
5. Remove the lower cushion.
6. Lower the hoist enough in order to leave the body supported by the jack stands.
7. Remove the upper cushion.
8. Remove the shims, if equipped.

1. Install the shims, if equipped.
2. Install the upper cushion.
3. Raise the frame slightly on the hoist.
4. Install the lower cushion.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the frame cushion bolts.

Tighten
Tighten the bolts to 70 N·m (52 lb ft).

6. Lower the hoist.

Drivetrain and Front Suspension Frame Insulator Replacement 4-Door Utility

Important: Properly support the frame when you change the frame cushions. If only one cushion is changed, lower the entire side on which the cushion in placed in order to provide clearance for the cushion.

1. Raise the vehicle slightly on a hoist. Refer to Lifting and Jacking the Vehicle in General Information.



2. Place jack stands under the body on the side of the vehicle that the cushions will be placed.



3. Remove the frame cushion bolts.
4. Remove the retainer.
5. Remove the lower cushion.
6. Lower the hoist enough in order to leave the body supported by the jack stands.
7. Remove the upper cushion.
8. Remove the shims, if equipped.

1. Install the shims, if equipped.
2. Install the upper cushion.
3. Raise the frame slightly on the hoist.
4. Install the lower cushion.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

5. Install the frame cushion bolts.

Tighten
Tighten the bolts to 70 N·m (52 lb ft).

6. Lower the hoist.