GM Service Manual Online
For 1990-2009 cars only

Blower Motor Replacement C60, C68

Removal Procedure

  1. Remove the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 4.3L.
  2. Remove the coolant reservoir. Refer to Coolant Recovery Reservoir Replacement in Engine Cooling.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the electrical connector from the blower motor.
  5. Position the PCM harness connectors out of the way.

  6. Object Number: 661752  Size: SH
  7. Remove the blower motor access cover retaining screws.
  8. Important: Cut through the cover as straight as possible because the access cover must be replaced. Part of this repair is visible to the customer. In order to prevent damage to the component, do not cut any deeper than necessary in order to remove the access cover.

  9. Cut through the cover on the cut line using a razor blade or a sharp utility knife.

  10. Object Number: 394171  Size: SH
  11. Disconnect the cooling tube from the blower motor.
  12. Disconnect the electrical connector from the blower motor.
  13. Remove the blower motor mounting bolts.
  14. Remove the blower motor.

Installation Procedure

  1. Install the blower motor.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the blower motor mounting bolts.
  4. Tighten
    Tighten the bolts to 4.5 N·m (40 lb in).


    Object Number: 394171  Size: SH
  5. Connect the cooling tube to the blower motor.

  6. Object Number: 661752  Size: SH
  7. Install the blower motor access cover.
  8. Install the blower motor access cover retaining screws.
  9. Tighten
    Tighten the screws to 2.5 N·m (22 lb in).

    Important: Do not use RTV. Apply the adhesive bead as straight as possible. Allow the adhesive to set for 15 minutes or until the adhesive becomes tacky.

  10. Seal the cut line using black weather-strip adhesive.
  11. Connect the electrical connector to the blower motor.
  12. Reposition the PCM harness connectors.
  13. Install the rear coolant recovery reservoir mounting stud.
  14. Install the coolant reservoir. Refer to the Coolant Recovery Reservoir Replacement in Engine Cooling.
  15. Install the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 4.3L.

Blower Motor Replacement C42

Removal Procedure

  1. Disconnect the PCM. Refer to the appropriate procedure:
  2. •  Powertrain Control Module Replacement in Engine Controls - 2.2L
    •  Powertrain Control Module Replacement in Engine Controls - 4.3L
  3. Remove the coolant reservoir. Refer to Coolant Recovery Reservoir Replacement in Engine Cooling.

  4. Object Number: 394171  Size: SH
  5. Remove the rear coolant recovery reservoir mounting stud.
  6. Disconnect the cooling tube from the blower motor.

  7. Object Number: 513313  Size: SH
  8. Disconnect the electrical connector (1).
  9. Remove the blower motor mounting bolts (2).
  10. Remove the blower motor.

Installation Procedure


    Object Number: 513313  Size: SH
  1. Install the blower motor.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the blower motor mounting bolts (2).
  4. Tighten
    Tighten the bolts to 4.5 N·m (40 lb in).

  5. Connect the electrical connector (1).

  6. Object Number: 394171  Size: SH
  7. Connect the cooling tube to the blower motor.
  8. Install the rear coolant recovery reservoir mounting stud.
  9. Install the coolant reservoir. Refer to Coolant Recovery Reservoir Replacement in Engine Cooling.
  10. Install the PCM. Refer to the appropriate procedure:
  11. •  Powertrain Control Module Replacement in Engine Controls - 2.2L
    •  Powertrain Control Module Replacement in Engine Controls - 4.3L