Step | Action | Values | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
Schematic Reference: Wiper/Washer Schematics Connector End View Reference: Wiper/Washer Connector End Views DEFINITION:The windshield washer pump is inoperative. | ||||||||
1 | Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections? | -- | Go to Step 2 | |||||
2 |
Do the windshield washers operate normally? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | ||||
3 | Do the windshield washer wipers operate when the windshield washer switch is pressed? | -- | Go to Step 6 | Go to Step 4 | ||||
4 |
Is the resistance near the specified value? | 0.5 ohms | Go to Step 15 | Go to Step 5 | ||||
5 | Test the following circuits for open or high resistance.
Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 13 | ||||
6 |
Does the test lamp illuminate on both terminals? | -- | Go to Step 7 | Go to Step 9 | ||||
7 |
Does the test lamp illuminate? | -- | Go to Step 8 | Go to Step 10 | ||||
8 |
Does the test lamp illuminate? | -- | Go to Step 18 | Go to Step 11 | ||||
9 | Replace the underhood fuse block. Refer to Underhood Electrical Center or Junction Block Replacement in Wiring Systems. Did you complete the replacement? | -- | Go to Step 20 | -- | ||||
10 | Test the windshield washer relay control circuit for an open or high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 15 | ||||
11 | Test the windshield washer pump control circuit for an open or high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 12 | ||||
12 | Test the windshield washer pump ground circuit for an open or high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 17 | ||||
13 | Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 14 | ||||
14 | Replace the windshield wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column. Did you complete the replacement? | -- | Go to Step 20 | -- | ||||
15 | Inspect for poor connections at the windshield wiper motor module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 16 | ||||
16 | Replace the windshield wiper motor module. Did you complete the replacement? | -- | Go to Step 20 | -- | ||||
17 | Replace the windshield washer relay. Did you complete the replacement? | -- | Go to Step 20 | -- | ||||
18 | Inspect for poor connections at the windshield washer pump. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 20 | Go to Step 19 | ||||
19 | Replace the windshield washer pump. Refer to Washer Pump Replacement . Did you complete the replacement? | -- | Go to Step 20 | -- | ||||
20 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 3 | ||||
