Turn Signal Lamps Inoperative Domestic
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Lighting Diagnostic System Check? | -- | Go to Step 2 | |
2 | Turn the hazard flashers ON. Do the hazard flashers operate? | -- | Go to Step 3 | Go to Step 4 |
3 |
Does the test lamp light? | -- | Go to Step 5 | Go to Step 6 |
4 |
Does the test lamp light? | -- | Go to Step 9 | Go to Step 10 |
5 |
Does the test lamp light? | -- | Go to Step 7 | Go to Step 8 |
6 | Repair the open in CKT 139 (PNK) from connector C201 to the instrument panel fuse block. Is the repair complete? | -- | Go to Step 18 | -- |
7 | Repair the open in CKT 1508 (LT BLU) between the turn/hazard switch and splice S250. Is the repair complete? | -- | Go to Step 18 | -- |
8 | Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering. Is the replacement complete? | -- | Go to Step 18 | -- |
9 | Connect a test lamp from CKT 550 (BLK) cavity G8 to CKT 62 (LT GRN) cavity H9 at the turn/hazard flasher module. Does the test lamp light? | -- | Go to Step 13 | Go to Step 14 |
10 | Inspect for an open in CKT 62 (LT GRN) from the turn/hazard flasher module to the turn/hazard switch. Did you find an open? | -- | Go to Step 11 | Go to Step 12 |
11 | Repair the open in CKT 62 (LT GRN) from the turn/hazard flasher module to the turn/hazard switch. Is the repair complete? | -- | Go to Step 18 | -- |
12 | Replace the turn/hazard switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering. Is the replacement complete? | -- | Go to Step 18 | -- |
13 |
Does the test lamp flash? | -- | Go to Step 8 | Go to Step 15 |
14 | Repair the open in CKT 550 (BLK) between the turn/hazard flasher module and ground G105. Is the repair complete? | -- | Go to Step 18 | -- |
15 | Use a test lamp in order to backprobe from the turn/hazard flasher module CKT 16 (PPL) cavity H7 to ground. Does the test lamp light? | -- | Go to Step 16 | Go to Step 17 |
16 | Repair the open in CKT 16 (PPL) from the turn/hazard flasher module to the turn/hazard switch. Is the repair complete? | -- | Go to Step 18 | -- |
17 | Replace the turn/hazard flasher module. Is the replacement complete? | -- | Go to Step 18 | -- |
18 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
Turn Signal Lamps Inoperative VE1
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Lighting Diagnostic System Check? | -- | Go to Step 2 | |
2 | Check Turn-B/U Fuse 16 at the I/P Fuse block. Is the fuse functional? | -- | Go to Step 4 | Go to Step 3 |
3 | Locate and repair overload and replace Turn-B/U Fuse. Is the repair complete? | -- | Go to Step 19 | -- |
4 | Turn Hazard Flashers ON. Do Hazard Flashers Operate? | -- | Go to Step 5 | Go to Step 7 |
5 |
Does Test Lamp Light? | -- | Go to Step 6 | Go to Step 11 |
6 |
Does Test Lamp Light? | -- | Go to Step 12 | Go to Step 13 |
7 |
Does Test Lamp Light? | -- | Go to Step 8 | Go to Step 14 |
8 | Connect a test lamp from CKT 550 (BLK) wire cavity G8 to CKT 62 (LT GRN) wire cavity H9 at the Turn/Hazard Flasher Module. Does Test Lamp Light? | -- | Go to Step 9 | Go to Step 15 |
9 |
Does Test Lamp Flash? | -- | Go to Step 16 | Go to Step 10 |
10 | Using a test lamp, backprobe from the Turn/Hazard Flasher Module CKT 16 (PPL) wire cavity H7 to ground. Does Test Lamp Flash? | -- | Go to Step 17 | Go to Step 18 |
11 | Locate and repair open in CKT 139 (PNK) wire from Connector C201 to I/P Fuse Block. Is the repair complete? | -- | Go to Step 19 | -- |
12 | Locate and repair open in CKT 1508 (LT BLU) wire between Turn/Hazard Switch and S250. Is the repair complete? | -- | Go to Step 19 | -- |
13 | Replace Turn Signal Switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle . Is the Repair complete? | -- | Go to Step 19 | -- |
14 | Locate and repair open in CKT 62 (LT GRN) wire from Turn/Hazard Flasher Module to Turn/Hazard Switch. Was a repair made? | -- | Go to Step 19 | Go to Step 16 |
15 | Locate and repair open in CKT 550 (BLK) wire between Turn/Hazard Flasher Module and G105. Is the repair complete? | -- | Go to Step 19 | -- |
16 | Replace Turn Signal Switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle . Is the repair complete? | -- | Go to Step 19 | -- |
17 | Locate and repair open in CKT 16 (PPL) wire from Turn/Hazard Flasher Module to Turn/Hazard Switch. Is the repair complete? | -- | Go to Step 19 | -- |
18 | Replace Turn/Hazard Flasher Module. Is the repair complete? | -- | Go to Step 19 | -- |
19 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
