Circuit Description (DTC C0269)
The EBCM microprocessor grounds the dump coil to energize and close the dump valve. This will release the excessive brake pressure which was applied by the driver to the wheels. If the EBCM microprocessor generates a dump command on one or more wheel for greater than nine seconds, the DTC will set (C0269).
Circuit Description (DTC C0274)
The EBCM microprocessor grounds the isolation coil to energize and close the isolation valve. This will prevent any additional brake pressure applied by the driver from reaching the wheel. Further increases in brake pressure will be prohibited. Each isolation valve is closed independently to isolate each wheel. The EBCM microprocessor also uses a software subroutine to monitor for any ABS event which would initiate an isolation command. This subroutine is performed every 1.0 second.
Conditions for Setting the DTC (C0269)
- Locked rotors.
- Braking on excessively slippery surfaces for greater than 9 seconds.
Conditions for Setting the DTC (C0274)
Isolation time (pressure hold) exceeding 255 consecutive 1.0 second checks.
Action Taken When the DTC Sets (C0269)
If the EBCM microprocessor generates a dump command on one or more wheel for greater than nine seconds, this feature will be activated. If either front channel detects this excessive dumping, the system will revert to a rear only ABS. If the rear channel detects excessive dumping, all ABS activity stops.
DTC C0269 is an ignition latched DTC, which indicates that the above actions remain true until the ignition switch is turned to OFF (even if the cause of the DTC is intermittent).
DTC C0269 is a DRP critical DTC, which means that DRP is disabled and the BRAKE indicator lamp will also light.
Action Taken When the DTC Sets (C0274)
| • | The ABS indicator lamp turns on |
| • | The ABS disables |
DTC C0274 is an ignition latched DTC, which indicates that the above actions remain true until the ignition switch is turned to OFF (even if the cause of the DTC is intermittent).
DTC C0274 is a DRP critical DTC, which means that DRP is disabled and the BRAKE indicator lamp will also light.
Conditions for Clearing the DTC (DTCs C0269/C0274)
| • | Repair the conditions responsible for setting the DTC |
| • | Use the Scan Tool Clear DTCs function |
Diagnostic Aids
Repair any other DTCs first. Then perform the Function Test of the scan tool in order to ensure proper operation of the ABS.
Test Description
The numbers below refer to the steps in the diagnostic table:
-
This step determines the resistance of the power ground circuit.
-
This step determines the battery voltage available to the EBCM.
-
This step determines the resistance of the signal ground circuit.
-
This step determines the ignition voltage available to the EBCM.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Diagnostic System Check performed? | -- | Go to Step 2 | |
2 |
Is the connector in good condition? | -- | Go to Step 3 | Go to Step 11 |
Measure the resistance between terminal B of the 2-way EBCM harness connector and the ground using a J 39200 . Is the resistance measurement within the specified range? | 0-2ohms | Go to Step 4 | Go to Step 12 | |
Measure the voltage between terminal A of the 2-way EBCM harness connector and the ground using a J 39200 . Is the voltage equal to or greater than the specified value? | 10.0 V | Go to Step 6 | Go to Step 5 | |
5 | Inspect the 60-amp ABS MaxiFuse®. Is the fuse open? | -- | Go to Step 13 | Go to Step 14 |
6 |
Is the connector in good condition? | -- | Go to Step 7 | Go to Step 15 |
Measure the resistance between terminal J of the 10-way EBCM harness connector and the ground using a J 39200 . Is the resistance measurement within the specified range? | 0-2ohms | Go to Step 8 | Go to Step 16 | |
Is the voltage equal to or greater than the specified value? | 10.0 V | Go to Step 10 | Go to Step 9 | |
9 | Inspect the 10-amp BRAKE fuse. Is the fuse open? | -- | Go to Step 17 | Go to Step 18 |
10 |
Does the DTC set as a current DTC? | -- | Go to Step 19 | Malfunction is intermittent. Go to Diagnostic Aids |
11 | Repair the 2-way EBCM harness connector. Refer to Connector Repairs . Is the repair complete? | -- | -- | |
12 | Repair the open or the high resistance in the CKT 650. Is the repair complete? | -- | -- | |
13 | Repair the short to ground in the CKT 442. Is the repair complete? | -- | -- | |
14 | Repair the open or the high resistance in the CKT 442. Is the repair complete? | -- | -- | |
15 | Repair the 10-way EBCM harness connector. Refer to Connector Repairs . Is the repair complete? | -- | -- | |
16 | Repair the open or the high resistance in the CKT 650. Is the repair complete? | -- | -- | |
17 | Repair the short to ground in the CKT 441. Is the repair complete? | -- | -- | |
18 | Repair the open or the high resistance in the CKT 441. Is the repair complete? | -- | -- | |
19 | Replace the EBCM. Refer to Electronic Brake Control Module Replacement . Is the repair complete? | -- | -- |
