| Table 1: | Folding Top Module Scan Tool Data Parameters |
| Table 2: | Folding Top Module Scan Tool Output Controls |
Parameter | System State | Expected Value | Description |
|---|---|---|---|
Operating Conditions: Ignition ON | |||
Battery Voltage Signal | -- | Varies | This displays Volts. This is the current battery voltage signal. |
Deck Lid Ajar Status | -- | Deck Closed / Known | The scan tool displays Deck Ajar/Deck Closed or Known/Unknown. This is the state of the deck lid ajar switch. |
Deck Lid Extended | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the deck lid. |
Deck Lid Latch Status | -- | Cleared | The scan tool displays Cleared or Not Cleared. This is the state of the deck lid latch. |
Deck Lid Latch Switch | -- | Deck Closed | The scan tool displays Deck Open or Deck Closed. This is the state of the deck lid latch switch. |
Driver Window Operation | -- | Varies | The scan tool displays Enabled or Disabled. This is the current state of the driver window system operation. |
Folding Top Calibrated | -- | Yes | The scan tool displays Yes or No. Yes is displayed if the folding top is calibrated properly. |
Folding Top Close Reference Position | -- | Varies | This displays Counts. This is the close reference position of the folding top measured in counts. |
Folding Top Open Reference Position | -- | Varies | This displays Counts. This is the open reference position of the folding top measured in counts. |
Folding Top Position Sensor | -- | Varies | This displays Counts. This is the position of the folding top measured in counts. |
Folding Top Status | -- | Varies | The scan tool displays Invalid, Retracted, Extended or Mid. This is the state of the folding top. |
Front Tonneau Close Reference Position | -- | Varies | This displays Counts. This is the close reference position of the front tonneau measured in counts. |
Front Tonneau Open Reference Position | -- | Varies | This displays Counts. This is the open reference position of the front tonneau measured in counts. |
Front Tonneau Position Sensor | -- | Varies | This displays Counts. This is the position of the front tonneau measured in counts. |
Front Tonneau Status | -- | Tonneau Closed | The scan tool displays Tonneau Open, Tonneau Closed or Mid. This is the state of the front tonneau. |
Header Latch Limit Switches | -- | Latched | The scan tool displays Invalid, Latched, Unlatched or Mid. This is the state of the header latch limit switches. |
Left Front Window Status | -- | OK | The scan tool displays OK or Out Of Limit. This is the state of the left front window. |
Limit Switch Supply Voltage | -- | Present | The scan tool displays Present or Not Present. This is the state of the limit switch supply voltage. |
Luggage Barrier In Place | -- | Yes | The scan tool displays Yes or No. Yes is displayed if the luggage barrier is in place. |
Luggage Barrier Limit Switch | -- | Varies | The scan tool displays Open or Closed. This is the state of the luggage barrier limit switch. |
Motor Command | -- | Varies | This displays amps. |
Motor Feedback Current | -- | OK | The scan tool displays OK or High. This is the state of the motor feedback. |
Motor X Direction Command | -- | Off | The scan tool displays On of Off. This is the state of motor X. |
Motor Y Direction Command | -- | Off | The scan tool displays On of Off. This is the state of motor Y. |
Passenger Window Operation | -- | Varies | The scan tool displays Enabled or Disabled. This is the current state of the passenger window system operation. |
Passenger Window Position Status | -- | OK | The scan tool displays OK or Out Of Limit. This is the state of the passenger window. |
Position Sensors Status | -- | OK | The scan tool displays OK or Error. This is the state of the position sensors. |
Power Mode Active | -- | Yes | The scan tool displays Yes or No. This is the state of the power mode. |
Pump Motor Temp. Sensor | -- | Varies | This displays Counts. This is the pump motor temperature measured in counts. |
Pump Over Temperature Sensor | -- | Normal | The scan tool displays Normal or Overtemp. This is the state of the pump temperature. |
Rear Compartment Lid Pull Down Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the rear compartment lid pull down switch. |
Rear Tonneau Close Reference Position | -- | Varies | This displays Counts. This is the close reference position of the rear tonneau measured in counts. |
Rear Tonneau Open Reference Position | -- | Varies | This displays Counts. This is the open reference position of the rear tonneau measured in counts. |
Rear Tonneau Position Sensor | -- | Varies | This displays Counts. This is the position of the rear tonneau measured in counts. |
Rear Tonneau Status | -- | Tonneau Closed | The scan tool displays Tonneau Open, Tonneau Closed or Mid. This is the state of the rear tonneau. |
System Timer | -- | OK | The scan tool displays OK or Expired. This is the state of the system timer. |
System Voltage | -- | OK | The scan tool displays OK or Low. This is the state of the system voltage. |
Too Cold For Top Operation | -- | No | The scan tool displays Yes or No. Yes is displayed if the temperature is too cold for top operation. |
Top Closed Limit Switch | -- | Off | The scan tool displays On or Off. This is the state of the top closed limit switch. |
Top Control | -- | Enabled | The scan tool displays Enabled or Inhibited. This is the state of the top control. |
Top Control Switch | -- | Idle | The scan tool displays Idle, Top Open, Top Closed or Invalid. This is the state of the top control switch. |
Top Position Error | -- | No | The scan tool displays Yes or No. Yes is displayed if there was a top position error. |
Trunk Control | -- | Enabled | The scan tool displays Enabled or Inhibited. This is the state of the trunk control. |
Valet Status | -- | Varies | The scan tool displays Active or Inactive. This is the state of the valet. |
Valve 1-5 Command | -- | Off | The scan tool displays On or Off. This is the state of the commanded corresponding valve. |
Vehicle In Park | -- | Yes | The scan tool displays Yes or No. Yes is displayed if the vehicle is in park. |
Output Control | Description |
|---|---|
Pump Motor A Direction | The FTC module commands to operate in the A direction. The motor should operate in the requested direction. |
Pump Motor B Direction | The FTC module commands to operate in the B direction. The motor should operate in the requested direction. |
Valve 1 Command | The FTC module commands Valve 1 to energize or not. As the valve is energized, a click can be heard, activating the valve. |
Valve 2 Command | The FTC module commands Valve 2 to energize or not. As the valve is energized, a click can be heard, activating the valve. |
Valve 3 Command | The FTC module commands Valve 3 to energize or not. As the valve is energized, a click can be heard, activating the valve. |
Valve 4 Command | The FTC module commands Valve 4 to energize or not. As the valve is energized, a click can be heard, activating the valve. |
Valve 5 Command | The FTC module commands Valve 5 to energize or not. As the valve is energized, a click can be heard, activating the valve. |
