GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0102: Mass Air Flow (MAF) Sensor Circuit Low Frequency

DTC P0103: Mass Air Flow (MAF) Sensor Circuit High Frequency

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

Ignition 1 Voltage

P0033, P0102

P0101

P0102

P0690

P0101, P0103

MAF Sensor Signal

P0102

P0102

P0102

P0102

P0101, P0103

Ground

--

P0102

P0102

--

P0102

Typical Scan Tool Data

MAF Sensor

Circuit

Short to Ground

Open

Short to Voltage

Operating Conditions: Engine running at various operating conditions

Parameter Normal Range: 1,750 Hz to 9,500 Hz

Ignition 1 Voltage

0 Hz

0 Hz

--

MAF Sensor Signal

0 Hz

0 Hz

0 Hz

Ground

--

0 Hz

--

Circuit/System Description

The mass air flow (MAF) sensor is integrated with the intake air temperature (IAT) sensor. The MAF sensor is an air flow meter that measures the amount of air entering the engine. The engine control module (ECM) uses the MAF sensor signal to provide the correct fuel delivery for all engine speeds and loads. A small quantity of air entering the engine indicates a deceleration or idle condition. A large quantity of air entering the engine indicates an acceleration or high load condition. The MAF/IAT sensor has the following circuits:

    • An ignition 1 voltage circuit
    • A ground circuit
    • A MAF sensor signal circuit
    • An IAT sensor signal circuit
    • A low reference circuit

The ECM applies 5 volts to the MAF sensor on the MAF sensor signal circuit. The sensor uses the voltage to produce a frequency based on the inlet air flow through the sensor bore. The frequency varies within a range of near 2,000 Hertz at idle to near 9,500 Hertz at maximum engine load.

Conditions for Running the DTC

    • The engine is running for greater than 1 second.
    • The engine speed is running.
    • The ignition 1 signal is greater than 8 volts.
    • The above conditions are met for greater than 1 second.
    • This DTC runs continuously within the enabling conditions.

Conditions for Setting the DTC

P0102

The ECM detects that the MAF Sensor parameter is less than 10 Hz for greater than 5 seconds.

P0103

The ECM detects that the MAF Sensor parameter is more than 14,500 Hz for greater than 5 seconds.

Action Taken When the DTC Sets

DTC P0102 and P0103 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTC P0102 and P0103 are Type B DTCs.

Diagnostic Aids

    • A wide open throttle (WOT) acceleration from a stop should cause the MAF sensor parameter on the scan tool to increase rapidly. This increase should be from 6-10 g/s at idle to 380 g/s or more at the time of the 1-2 shift.
    • Verify that any electrical aftermarket devices are properly connected and grounded. Refer to Checking Aftermarket Accessories.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Special Tools

J 38522 Variable Signal Generator

Circuit/System Verification

  1. Engine running, observe the scan tool MAF Sensor parameter. The reading should be between 1,700-3,800 Hz depending on the engine coolant temperature (ECT).
  2. A wide open throttle (WOT) acceleration from a stop should cause the MAF sensor parameter on the scan tool to increase rapidly. This increase should be from 2-6 g/s at idle to greater than 180 g/s at the time of the 1-2 shift.
  3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

  1. Verify the integrity of the air induction system by inspecting for the following conditions:
  2. • Damaged components
    • Loose or improper installation
    • An air flow restriction
    • Any vacuum leak
    • Water intrusion
  3. Ignition OFF, disconnect the harness connector at the MAF/IAT sensor.
  4. Ignition OFF and scan tool disconnected for 90 seconds, test for less than 5 ohms between the MAF ground circuit terminal B and ground.
  5. If greater than the specified range, test the ground circuit for an open/high resistance.
  6. Ignition ON, test for 4.8-5.2 volts between the MAF signal circuit terminal A and ground.
  7. If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM.
    If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the ECM.
  8. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal C and ground.
  9. If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
  10. Ignition OFF, connect the red lead of the J 38522 to the signal circuit terminal A at the MAF/IAT sensor harness connector. Connect the battery voltage supply to B+. Connect the black lead to ground.
  11. Set the J 38522 signal to 5 volts, the Frequency to 5K, and the Duty Cycle to Normal.
  12. Engine idling, observe the scan tool MAF Sensor parameter. The scan tool MAF Sensor parameter should be between 4,950-5,025 Hz.
  13. If the MAF Sensor parameter is not within the specified range, replace the ECM.
  14. If all circuits test normal, test or replace the MAF sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Mass Airflow Sensor/Intake Air Temperature Sensor Replacement
    •  Control Module References for ECM replacement, setup, and programming