Circuit Description
The engine oil level switch grounds when the oil level is at the proper level. With the ignition ON, and the engine OFF, the engine control module (ECM) should detect full oil level or a low voltage on the signal circuit of the engine oil level switch. When the engine speed is at least 2,000 RPM, the ECM should detect a transition from a low voltage to a high voltage on the signal circuit of the engine oil level switch.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P1617 Engine Oil Level Switch Circuit
Conditions for Running the DTC
| • | The vehicle is travelling at a speed greater than 5 km/h (3 mph). |
| • | The throttle position is greater than 5 percent. |
| • | The engine speed is at least 2,000 RPM. |
| • | The vehicle is cruising and is not accelerating. |
| • | The following DTCs are not set: |
| - | P0122 |
| - | P0123 |
| - | P0506 |
| - | P0507 |
Conditions for Setting the DTC
| • | The ECM does not detect a transition from a low voltage to a high voltage, when the engine speed is at least 2,000 RPM. |
| • | The above condition is present for at least 5 minutes. |
| • | The condition may be present for up to 25 minutes before setting the DTC. |
Action Taken When the DTC Sets
The ECM records the operating conditions at the time when the diagnostic test fails. The ECM displays this information in the Failure Records on the scan tool.
Conditions for Clearing the DTC
| • | The DTC becomes history when the conditions for setting the DTC are no longer present. |
| • | The history DTC is cleared after 40 malfunction free warm-up cycles. |
| • | The ECM receives the clear code command from the scan tool. |
Diagnostic Aids
The Failure Records may help find an intermittent condition. If you cannot duplicate the DTC, the information in the Failure Records can help determine how many miles since the DTC set. The Fail Counter and the Pass Counter can also aid determining how many ignition cycles that the diagnostic test reported a pass and/or a fail.
Refer to Testing for Intermittent Conditions and Poor Connections .
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Instrument Cluster Schematics Connector End View Reference: Instrument Panel, Gages, and Console Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 |
Does the Engine Oil Level Switch parameter display Low? | Go to Diagnostic Aids | Go to Step 3 |
3 |
Does the Engine Oil Level Switch parameter display Low? | Go to Step 6 | Go to Step 4 |
4 | Test the signal circuit of the engine oil level switch for a short to ground. Refer to Circuit Testing and to Wiring Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 5 |
5 | Inspect for poor connections at the harness connector of the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 8 |
6 | Inspect for poor connections at the harness connector of the engine oil level switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs . Did you find and correct the condition? | Go to Step 9 | Go to Step 7 |
7 | Replace the engine oil level switch. Refer to Engine Oil Level Sensor and/or Switch Replacement for the 4.6L engine or Engine Oil Level Sensor and/or Switch Replacement for the 4.4L engine. Did you complete the replacement? | Go to Step 9 | -- |
8 | Replace the ECM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 9 | -- |
9 |
Does the DTC reset? | Go to Step 2 | System OK |
