GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2006 🢒 XLR 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 DTC P0608

Circuit Description

The engine control module (ECM) creates the vehicle speed output signal by pulsing the circuit to ground. The ECM monitors the voltage on the vehicle speed output circuit. If the ECM determines that the voltage is out of the normal operating range, a DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0608 Vehicle Speed Output Circuit

Conditions for Running the DTC
    • The engine speed is more than 400 RPM.
    • The ignition voltage is between 6-18 volts.

Conditions for Setting the DTC
    • The ECM detects that the commanded state of the driver and the actual state of the signal circuit do not match.
    • The above condition must be present for a minimum of 5 seconds.

Action Taken When the DTC Sets

The ECM records the operating conditions at the time the diagnostic fails. The ECM displays the failure information in the Failure Records on the scan tool.

Conditions for Clearing the MIL/DTC
    • The history DTC clears after 40 malfunction free warm-up cycles.
    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The powertrain control module (PCM) receives the clear code command from the scan tool.

Step

Action

Yes

No

Schematic Reference: Instrument Cluster Schematics

Connector End View Reference: Engine Control Module Connector End Views for the 4.4L engine or Engine Control Module Connector End Views for the 4.6L engine

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2
  1. Install a scan tool.
  2. Raise the vehicles drive wheels. Refer to Lifting and Jacking the Vehicle .
  3. Start the engine.
  4. Place the transmission into drive.
  5. With the scan tool, observe the Vehicle Speed parameter in the engine control module (ECM) Engine Data 2 data list.

Does the Vehicle Speed parameter match the speedometer display?

Go to Testing for Intermittent Conditions and Poor Connections

Go to Step 3

3
  1. Turn OFF the ignition.
  2. Disconnect the ECM connector C1.
  3. Install one lead of the J 33431-C Signal Generator and Instrument Panel Tester to the vehicle speed signal circuit at the ECM harness connector, and the other lead to a good ground.
  4. Turn ON the ignition, with the engine OFF.
  5. Set the J 33431-C to generate a speedometer signal.

Does the vehicle speedometer indicate approximately 55 MPH?

Go to Step 5

Go to Step 4

4

Test the vehicle speed signal circuit for the following:

    • An open
    • A short to voltage
    • A short to ground

Refer to Circuit Testing and to Wiring Repairs .

Did you find and correct the condition?

Go to Step 9

Go to Step 6

5

Inspect for poor connections at harness connector of the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs .

Did you find and correct the condition?

Go to Step 9

Go to Step 7

6

Inspect for poor connections at the harness connector of the instrument panel cluster (IPC). Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs .

Did you find and correct the condition?

Go to Step 9

Go to Step 8

7

Replace the ECM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 9

--

8

Replace the IPC. Refer to Control Module References for replacement, setup, and programming .

Did you complete the replacement?

Go to Step 9

--

9
  1. Use the scan tool in order to clear the DTCs.
  2. Operate vehicle within the Conditions for Running this DTC.

Does the DTC reset?

Go to Step 2

System OK