Circuit Description
An ignition voltage circuit and a ground circuit are supplied to the fuel pump control module. When the ignition switch is in the ON position, the fuel pump control module turns ON the fuel pump to full power within 24 ms. This facilitates rapid fuel prime for 500 ms. The engine control module (ECM) supplies a pulse width modulated (PWM) signal to the fuel pump control module on the fuel pump relay control circuit. The fuel pump control module varies the voltage to the fuel pump based on the signal from the ECM. If the fuel pump control module receives no fuel pump control signal from the ECM within 500 ms, the fuel pump control module will turn OFF output to the fuel pump.
At idle speed, the fuel pump control module sets the voltage potential to the fuel pump to 9.5 volts. This reduces fuel pump noise and vehicle system power requirements. When higher fuel volume is required, such as engine operation above idle, the fuel pump control module increases the voltage potential to the fuel pump to battery voltage.
The fuel pump control module also supplies the fuel pump speed output circuit and the fuel pump motor low reference circuit, which allows for enhanced fuel pump diagnostics. Therefore, the fuel pump control module is capable of diagnosing itself, the fuel pump relay control circuit, and the fuel pump performance. The diagnostic information is communicated from the fuel pump control module to the ECM through the fuel pump speed control feedback signal circuit.
If the ECM detects a zero percent duty cycle on the fuel pump speed control feedback signal circuit, DTC P1254 sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P1254 Fuel Pump Speed Control Feedback Circuit High Voltage
Conditions for Running the DTC
| • | The fuel pump is controlled by the fuel pump control module. |
| • | The ignition voltage is between 6-18 volts. |
| • | The ignition ON time is more than 2 seconds. |
| • | DTC P1254 runs continuously once the above conditions have been met. |
Conditions for Setting the DTC
| • | The ECM detects an open or a short to voltage on the fuel pump speed control feedback signal circuit. |
| OR |
| • | The ECM detects an open or a short to ground on the ignition 1 voltage circuit of the fuel pump control module. |
| OR |
| • | The ECM detects a short to ground on the fuel pump speed output circuit. |
| • | The above condition is present for more than 2 seconds. |
Action Taken When the DTC Sets
| • | The control module stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Failure Records. |
| • | The driver information center, if equipped, may display a message. |
Conditions for Clearing the DTC
| • | A current DTC Last Test Failed clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic. |
| • | Clear the DTC with a scan tool. |
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Controls Connector End Views or Engine Control Module Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Attempt to start the engine. Did the engine start and idle? | Go to Step 8 | Go to Step 3 |
3 | Inspect the fuel fuse in the underhood bussed electrical center (UBEC). Is the fuse open? | Go to Step 5 | Go to Step 4 |
4 |
Does the test lamp illuminate? | Go to Step 10 | Go to Step 7 |
5 | Test the fuel pump speed output circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 6 |
6 | Test the ignition 1 voltage circuit between the fuel pump control module and the UBEC for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 12 |
7 | Test the ignition 1 voltage circuit between the fuel pump control module and the UBEC for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 12 |
8 | Test the fuel pump motor low reference circuit and the ground circuit of the fuel pump control module for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 9 |
9 | Test the fuel pump speed control feedback signal circuit between the fuel pump control module and the engine control module (ECM) for an open and for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 11 |
10 | Test the ground circuit of the fuel pump control module for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 11 |
11 | Test for shorted terminals and for poor connections at the fuel pump control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 13 |
12 | Test for shorted terminals and for poor connections at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 15 | Go to Step 14 |
13 | Replace the fuel pump control module. Refer to Fuel Pump Control Module Replacement . Did you complete the replacement? | Go to Step 15 | -- |
14 | Replace the ECM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 15 | -- |
15 |
Did the DTC fail this ignition? | Go to Step 2 | Go to Step 16 |
16 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK |
