GM Service Manual Online
For 1990-2009 cars only

Object Number: 25443  Size: SF
Master Electrical Component List
Automatic Transmission Controls Schematics
OBD II Symbol Description Notice

Circuit Description

The PCM controls the torque converter clutch (TCC) solenoid valve pulse width modulation (PWM). The solenoid controls the hydraulic fluid for TCC apply and release. When the vehicle is accelerating, the PCM commands the TCC to be disengaged.

If the PCM detects a TCC slip from -20 to +150 RPM, when the TCC is commanded OFF, then DTC P0742 sets. DTC P0742 is a type B DTC.

Conditions for Running the DTC

    • No TP DTCs P0121, P0122 or P0123.
    • No VSS DTCs P0502 or P0503.
    • No AT ISS DTCs P0716 or P0717.
    • No TCC stuck OFF DTC P0741.
    • No IMS DTCs P1820, P1822, P1823, or P1825.
    • No TCC PWM solenoid valve DTC P1860.
    • The engine run time is greater than 5 seconds.
    • The IMS indicates D4.
    • The transmission gear ratio indicates 3rd or 4th gear.
    • The transmission fluid temperature is 20-133°C (68-271°F).
    • The TP angle is 20-90 percent.
    • The engine torque is 155-294 N·m (114-217 lb ft).
    • The vehicle speed is 16-130 km/h (10-80 mph).
    • The TCC is commanded OFF.

Conditions for Setting the DTC

The TCC slip speed is -20 to +150 RPM for 4.5 seconds, twice during the same trip.

Action Taken When the DTC Sets

    • The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.
    • The PCM inhibits TCC engagement.
    • The PCM freezes transmission adapt functions.
    • The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.
    • The PCM stores DTC P0742 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC

    • The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
    • A scan tool can clear the MIL/DTC.
    • The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.
    • The PCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids

    • Rapid fluctuation in line pressure may set DTC P0742. Refer to Line Pressure Check .
    • The customer may notice an engine stalling condition.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step verified that the PCM commanded the TCC PWM solenoid valve OFF and the slip speed is -20 to +150 RPM.

  2. This step inspects and repairs the components that caused the DTC to set.

DTC P0742

Step

Action

Value(s)

Yes

No

1

Did you perform the Powertrain Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls in Engine Controls

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM.

  4. Record the DTC Freeze Frame and Failure Records.
  5. Clear the DTC.
  6. Select TCC Duty Cycle and TCC Slip Speed on the scan tool.
  7. Drive the vehicle in D4, while in 4th gear command a TP angle greater than 20%.

While the TCC duty cycle is 0%, does the scan tool display a TCC slip speed within the specified parameters?

-20 to +150 RPM

Go to Step 3

Go to Diagnostic Aids

3

  1. Inspect for the following conditions:
  2. • The TCC PWM solenoid valve is stuck ON due to sediment.
    • Refer to Control Valve Upper Body Disassemble in the 4T80-E section of the Transmission Unit Repair Manual.
    • The TCC converter feed limit valve is stuck ON due to sediment.
    • Refer to Control Valve Upper Body Disassemble in the 4T80-E section of the Transmission Unit Repair Manual.
  3. Repair or replace any malfunctioning component.

Did you complete the repair?

--

Go to Step 4

--

4

Perform the following procedure in order to verify the repair:

  1. Select DTC.
  2. Select Clear Info.
  3. Operate the vehicle under the following conditions:
  4. • Drive the vehicle in D4 with a TP angle of 20-90% and a vehicle speed greater than 16 km/h (10 mph).
    • The TFT is 20-133°C (68-271°F).
    • The engine torque is 155-294 N·m (114-217 lb ft).
    • The TCC slip speed must be 175-1,500 RPM for 5 seconds.
  5. Select Specific DTC.
  6. Enter DTC P0742.

Has the test run and passed?

--

System OK

Go to Step 1