GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2000 🢒 Seville 🢒 Bulletins 🢒 Front/Rear Heated Seat Inoperative/Cold (Install Seat Heat Element)

Front/Rear Heated Seat Inoperative/Cold (Install Seat Heat Element)

Subject:Front/Rear Heated Seat Inoperative/Cold (Install Seat Heat Element)

Models:1998-2004 Cadillac Seville with RPO KA1


This bulletin is being revised to update the model year, VIN numbers and includes rear seat information. Please discard Corporate Bulletin Number 01-08-50-002B (Section 08-Body and Accessories).

Important: This service bulletin includes rear seat diagnostic and part information.

Condition

Some customers may comment that the front/rear seat assembly heat function is not operating properly. The front/rear seat back and seat cushion remain cold when the HEAT/OFF switch is activated.

Cause

This condition may be due to a non-functioning heat element in the front/rear heated seat back/cushion trim cover.

The heated seat system consists of four heated seats, two in the front and two in the rear.

Correction
  1. Determine which heat element is not functioning properly by measuring the resistance values of the factory heat elements. Refer to the appropriate diagnostic procedure (1st, 2nd or 3rd Design, Front/Rear) in this bulletin.
  2. If the resistance values of a factory heat element are NOT within the specified range, install a service heat element between the non-functioning factory heat element and the seat trim cover. Refer to the Service Heat Element Installation Procedure in this bulletin.

1st Design-Front Seat Heat Diagnostic Procedure for 1998-2000 MY Built BEFORE VIN YU204670
Object Number: 1315771 Size: MF

Location

Description

1

LH/RH Front Seat Back-Center Heat Element

2

LH/RH Front Seat Cushion-Center Heat Element

3

LH/RH Front Seat Cushion-Outer Heat Element

4

LH/RH Front Seat Cushion-Inner Heat Element

5

LH/RH Front Seat Back-Outer Heat Element

6

LH/RH Front Seat Back-Inner Heat Element

7

25755073(LH) or 25762972(RH) -Front Seat Back Heater Pkg

8

25755076-Front Seat Cushion Heater Pkg-LH/RH

  1. Adjust the front seat assembly to the maximum up and rearward position in order to access the seat cushion fasteners.

    2. Object Number: 669309 Size: SH
  2. Remove the fasteners (2) retaining the seat cushion (1) to the seat adjuster.
  3. Lift and support the seat cushion assembly away from the seat adjuster assembly.

    4. Object Number: 1315790 Size: SH
  4. Disconnect the heated seat module (3) harness green, 2-way connector (4).
  5. Measure the front seat back total element resistance between cavities A and B. Does the resistance measure less than 5 ohms?
    6. • If yes, go to Step 6.
    • If no, go to Step 12 in order to determine which of the three front seat back heat elements has a resistance value NOT within the specified range.
  6. Disconnect the heated seat module harness black, 4-way connector (5).

    7. Important: If the resistance is measured with the seat still warm, the resistance may vary outside of the specified range since the thermistor resistance varies with temperature.

  7. Measure the front seat cushion thermistor resistance between cavities C and D. Does the resistance measure between 280 ohms and 300K ohms?
    8. • If yes, go to Step 8.
    • If no, install a front seat cushion center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  8. Measure the front seat cushion total element resistance between cavities A and B. Does the resistance measure less than 5 ohms?
    9. • If yes, the resistance values of the front seat heat elements are within the specified range. To find the cause of the inoperative/cold heated seat, perform the standard diagnostic procedures in the Service Manual.
    • If no, go to Step 9 order to determine which of the three front seat cushion heat elements has a resistance value NOT within the specified range.

    Object Number: 295170 Size: SH
  9. Disconnect the white 2-way connectors between the seat cushion center heat element and the seat cushion outer and inner heat elements.
  10. Measure the seat cushion outer heat element resistance between cavities A and B at the white 2-way connector. Does the resistance measure less than 5 ohms?
    11. • If yes, go to Step 11.
    • If no, install a front seat cushion outer heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  11. Measure the seat cushion inner heat element resistance between cavities A and B at the white 2-way connector. Does the resistance measure less than 5 ohms?
    12. • If yes, install a front seat cushion center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
    • If no, install a front seat cushion inner heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  12. Remove the front seat assembly from the vehicle. Refer to Seat Replacement-Front Bucket in the Seats sub-section of the Service Manual.
  13. Remove the seat back trim panel in order to access the two white 2-way connectors. Refer to Seat Back Panel Replacement-Front in the Seats sub-section of the Service Manual.

    14. Object Number: 295170 Size: SH
  14. Disconnect the white 2-way connectors between the seat back center heat element and the seat back outer and inner heat elements.
  15. Measure the seat back outer heat element resistance between cavities A and B at the white 2-way connector. Does the resistance measure less than 5 ohms?
    16. • If yes, go to Step 16.
    • If no, install a front seat back outer heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  16. Measure the seat back inner heat element resistance between cavities A and B at the white 2-way connector. Does the resistance measure less than 5 ohms?
    17. • If yes, install a front seat back center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
    • If no, install a front seat back inner heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.

1st Design-Rear Seat Heat Diagnostic Procedure for 1998-2000 MY Built BEFORE VIN YU204670
Object Number: 1414736 Size: MF

Location

Description

1

LH/RH Rear Seat Back-Center Heat Element

2

LH/RH Rear Seat Cushion-Center Heat Element

3

LH/RH Rear Seat Cushion-Outer Heat Element

4

LH/RH Rear Seat Cushion-Inner Heat Element

5

LH/RH Rear Seat Back-Outer Heat Element

6

LH/RH Rear Seat Back-Inner Heat Element

7

25755082(LH) or 25762973(RH) -Rear Seat Back Heater Pkg

8

25755085(LH) or 25762974(RH)-Rear Seat Cushion Heater Pkg


    Object Number: 1414734 Size: MF
  1. Remove the rear seat cushion assembly (1) from the vehicle. Refer to Seat Cushion Replacement-Rear in the Seats sub-section of the Service Manual.

    2. Important: If the resistance is measured with the seat still warm, the resistance may vary outside of the specified range since the thermistor resistance varies with temperature.

  2. At the rear seat cushion blue, 8-way connector C320 (2), measure the thermistor resistance.
    3. • For the LH rear seat cushion, measure between cavities A and B.
    • For the RH rear seat cushion, measure between cavities E and F.
  3. Does the resistance measure between 280 ohms and 300 K ohms?
    4. • If yes, go to Step 4.
    • If no, install a LH/RH rear seat cushion (center) heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  4. At the blue, 8-way connector C320 (2), measure the rear seat cushion total element resistance.
    5. • For the LH rear seat cushion, measure between cavities C and D.
    • For the RH rear seat cushion, measure between cavities G and H.
  5. Does the resistance measure less than 5 ohms?
    6. • If yes, go to Step 10.
    • If no, go to Step 6 in order to determine which of the three rear seat cushion heat elements has a resistance value NOT within the specified range.
  6. Partially remove the trim cover from the rear seat cushion. Refer to Seat Cushion Cover Replacement-Rear in the Seats sub-section of the Service Manual.
  7. At the LH/RH rear seat cushion, disconnect the green 2-way connectors between the seat cushion center heat element and the seat cushion inner and outer heat elements.
  8. Measure the seat cushion inner heat element resistance between cavities A and B at the green 2-way connector. Does the resistance measure less than 5 ohms?
    9. • If yes, go to Step 9.
    • If no, install a LH/RH rear seat cushion inner heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  9. Measure the seat cushion outer heat element resistance between cavities A and B at the green 2-way connector. Does the resistance measure less than 5 ohms?
    10. • If yes, install a rear seat cushion center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
    • If no, install a LH/RH rear seat cushion outer heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  10. Remove the rear seat back assembly from the vehicle. Refer to Seat Back Replacement-Rear in the Seats sub-section of the Service Manual.
  11. At the LH/RH rear seat back heated seat module, disconnect the green, 2-way connector.
  12. Measure the rear seat back total element resistance between cavities A and B. Does the resistance measure less than 5 ohms?
    13. • If yes, the resistance values of the LH/RH rear seat heat back and cushion heat elements are within the specified range. To find the cause of the inoperative/cold rear heated seat, perform the standard diagnostic procedures in the Service Manual.
    • If no, disconnect the green 2-way connectors between the seat back center heat element and the seat back inner and outer heat elements.
  13. Measure the seat back inner heat element resistance between cavities A and B at the green 2-way connector. Does the resistance measure less than 5 ohms?
    14. • If yes, go to Step 14.
    • If no, install a rear seat back inner heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  14. Measure the seat back outer heat element resistance between cavities A and B at the green 2-way connector. Does the resistance measure less than 5 ohms?
    15. • If yes, install a rear seat back center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
    • If no, install a rear seat back outer heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.

2nd Design-Front Seat Diagnostic Procedure for 2000 MY Built AFTER VIN YU204669 to 2001 MY Built BEFORE VIN 1U228114
Object Number: 1315787 Size: MF

Location

Description

1

LH/RH Front Seat Back-Center Heat Element

2

LH/RH Front Seat Cushion-Center Heat Element

3

LH/RH Front Seat Cushion-Outer Heat Element

4

LH/RH Front Seat Cushion-Inner Heat Element

5

25755074-Front Seat Back Heater Pkg-LH/RH

6

25755077-Front Seat Cushion Heater Pkg-LH/RH

  1. Adjust the front seat assembly to the maximum up and rearward position in order to access the seat cushion fasteners.

    2. Object Number: 669309 Size: SH
  2. Remove the fasteners (2) retaining the seat cushion (1) to the seat adjuster.
  3. Lift and support the seat cushion assembly away from the seat adjuster assembly.

    4. Object Number: 1315790 Size: SH
  4. Disconnect the heated seat module (3) harness green, 2-way connector (4).
  5. Measure the front seat back total element resistance between cavities A and B. Does the resistance measure less than 5 ohms?
    6. • If yes, go to Step 6.
    • If no, install a front seat back heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  6. Disconnect the heated seat module harness black, 4-way connector (5).

    7. Important: If the resistance is measured with the seat still warm, the resistance may vary outside of the specified range since the thermistor resistance varies with temperature.

  7. Measure the front seat cushion thermistor resistance between cavities C and D. Does the resistance measure between 280 ohms and 300K ohms?
    8. • If yes, go to Step 8.
    • If no, install a front seat cushion center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  8. Measure the front seat cushion total element resistance between cavities A and B. Does the resistance measure less than 5 ohms?
    9. • If yes, the resistance values of the front seat heat elements are within the specified range. To find the cause of the inoperative/cold heated seat, perform the standard diagnostic procedures in the Service Manual.
    • If no, go to Step 9 in order to determine which of the three front seat cushion heat elements has a resistance value NOT within the specified range.

    Object Number: 295170 Size: SH
  9. Disconnect the white 2-way connectors between the seat cushion center heat element and the seat cushion outer and inner heat elements.
  10. Measure the seat cushion outer heat element resistance between cavities A and B at the white 2-way connector. Does the resistance measure less than 5 ohms?
    11. • If yes, go to Step 11.
    • If no, install a front seat cushion outer heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  11. Measure the seat cushion inner heat element resistance between cavities A and B at the white 2-way connector. Does the resistance measure less than 5 ohms?
    12. • If yes, install a front seat cushion center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
    • If no, install a front seat cushion inner heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.

2nd Design-Rear Seat Diagnostic Procedure for 2000 MY Built AFTER VIN YU204669 to 2001 MY Built BEFORE VIN 1U228114
Object Number: 1414738 Size: MF

Location

Description

1

LH/RH Rear Seat Back-Center Heat Element

2

LH/RH Rear Seat Cushion-Center Heat Element

3

LH/RH Rear Seat Cushion-Outer Heat Element

4

LH/RH Rear Seat Cushion-Inner Heat Element

5

25755083 -Rear Seat Back Heater Pkg-LH/RH

6

25755086(LH) or 25762975(RH)-Rear Seat Cushion Heater Pkg


    Object Number: 1414734 Size: MF
  1. Remove the rear seat cushion assembly (1) from the vehicle. Refer to Seat Cushion Replacement-Rear in the Seats sub-section of the Service Manual.

    2. Important: If the resistance is measured with the seat still warm, the resistance may vary outside of the specified range since the thermistor resistance varies with temperature.

  2. At the rear seat cushion blue, 8-way connector C320 (2), measure the thermistor resistance.
    3. • For the LH rear seat cushion, measure between cavities A and B.
    • For the RH rear seat cushion, measure between cavities E and F.
  3. Does the resistance measure between 280 ohms and 300 K ohms?
    4. • If yes, go to Step 4.
    • If no, install a LH/RH rear seat cushion (center) heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  4. At the blue, 8-way connector C320 (2), measure the rear seat cushion total element resistance.
    5. • For the LH rear seat cushion, measure between cavities C and D.
    • For the RH rear seat cushion, measure between cavities G and H.
  5. Does the resistance measure less than 5 ohms?
    6. • If yes, go to Step 10.
    • If no, go to Step 6in order to determine which of the three rear seat cushion heat elements has a resistance value NOT within the specified range.
  6. Partially remove the trim cover from the rear seat cushion. Refer to Seat Cushion Cover Replacement-Rear in the Seats sub-section of the Service Manual.
  7. At the LH/RH rear seat cushion, disconnect the green 2-way connectors between the seat cushion center heat element and the seat cushion inner and outer heat elements.
  8. Measure the seat cushion inner heat element resistance between cavities A and B at the green 2-way connector. Does the resistance measure less than 5 ohms?
    9. • If yes, go to Step 9.
    • If no, install a LH/RH rear seat cushion inner heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  9. Measure the seat cushion outer heat element resistance between cavities A and B at the green 2-way connector. Does the resistance measure less than 5 ohms?
    10. • If yes, install a rear seat cushion center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
    • If no, install a LH/RH rear seat cushion outer heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  10. Remove the rear seat back assembly from the vehicle. Refer to Seat Back Replacement-Rear in the Seats sub-section of the Service Manual.
  11. At the LH/RH rear seat back heated seat module, disconnect the green, 2-way connector.
  12. Measure the rear seat back total element resistance between cavities A and B. Does the resistance measure less than 5 ohms?
    13. • If yes, the resistance values of the LH/RH rear seat heat back and cushion heat elements are within the specified range. To find the cause of the inoperative/cold rear heated seat, perform the standard diagnostic procedures in the Service Manual.
    • If no, install a rear seat back center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.

3rd Design-Front Seat Diagnostic Procedure for 2001 MY Built AFTER VIN 1U228113 thru 2004 MY
Object Number: 1315789 Size: MF

Location

Description

1

LH/RH Front Seat Back-Center Heat Element

2

LH/RH Front Seat Cushion-Center Heat Element

3

25755075-Front Seat Back Heater Pkg-LH/RH

4

25755078-Front Seat Cushion Heater Pkg-LH/RH

  1. Adjust the front seat assembly to the maximum up and rearward position in order to access the seat cushion fasteners.

    2. Object Number: 669309 Size: SH
  2. Remove the fasteners (2) retaining the seat cushion (1) to the seat adjuster.
  3. Lift and support the seat cushion assembly away from the seat adjuster assembly.

    4. Object Number: 1315790 Size: SH
  4. Disconnect the heated seat module (3) harness green, 2-way connector (4).
  5. Measure the front seat back total element resistance between cavities A and B. Does the resistance measure less than 5 ohms?
    6. • If yes, go to Step 6.
    • If no, install a front seat back heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  6. Disconnect the heated seat module harness black, 4-way connector (5).

    7. Important: If the resistance is measured with the seat still warm, the resistance may vary outside of the specified range since the thermistor resistance varies with temperature.

  7. Measure the front seat cushion thermistor resistance between cavities C and D. Does the resistance measure between 280 ohms and 300K ohms?
    8. • If yes, go to Step 8.
    • If no, install a front seat cushion heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  8. Measure the front seat cushion total element resistance between cavities A and B. Does the resistance measure less than 5 ohms?
    9. • If yes, the resistance values of the front seat heat elements are within the specified range. To find the cause of the inoperative/cold heated seat, perform the standard diagnostic procedures in the Service Manual.
    • If no, install a front seat cushion heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.

3rd Design-Rear Seat Diagnostic Procedure for 2001 MY Built AFTER VIN 1U228113 thru 2004 MY
Object Number: 1414739 Size: MF

Location

Description

1

LH/RH Rear Seat Back-Center Heat Element

2

LH/RH Rear Seat Cushion-Center Heat Element

3

25755084 -Rear Seat Back Heater Pkg-LH/RH

4

25755087-Rear Seat Cushion Heater Pkg-LH/RH


    Object Number: 1414734 Size: MF
  1. Remove the rear seat cushion assembly (1) from the vehicle. Refer to Seat Cushion Replacement-Rear in the Seats sub-section of the Service Manual.

    2. Important: If the resistance is measured with the seat still warm, the resistance may vary outside of the specified range since the thermistor resistance varies with temperature.

  2. At the rear seat cushion blue, 8-way connector C320 (2), measure the thermistor resistance.
    3. • For the LH rear seat cushion, measure between cavities A and B.
    • For the RH rear seat cushion, measure between cavities E and F.
  3. Does the resistance measure between 280 ohms and 300 K ohms?
    4. • If yes, go to Step 4.
    • If no, install a LH/RH rear seat cushion (center) heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  4. At the blue, 8-way connector C320 (2), measure the rear seat cushion total element resistance.
    5. • For the LH rear seat cushion, measure between cavities C and D.
    • For the RH rear seat cushion, measure between cavities G and H.
    • If yes, go to Step 4.
    • If no, install a rear seat cushion center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  5. Does the resistance measure less than 5 ohms?
    6. • If yes, go to Step 6.
    • If no, install a rear seat cushion center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.
  6. Remove the rear seat back assembly from the vehicle. Refer to Seat Back Replacement-Rear in the Seats sub-section of the Service Manual.
  7. At the LH/RH rear seat back heated seat module, disconnect the green, 2-way connector.
  8. Measure the rear seat back total element resistance between cavities A and B. Does the resistance measure less than 5 ohms?
    9. • If yes, the resistance values of the LH/RH rear seat heat back and cushion heat elements are within the specified range. To find the cause of the inoperative/cold rear heated seat, perform the standard diagnostic procedures in the Service Manual.
    • If no, install a rear seat back center heat element. Refer to the Service Heat Element Installation Procedure in this bulletin.

Service Heat Element Installation Procedure

If a sublet trim repair facility is used, please provide a copy of this bulletin to the repair shop.

Important: Before installing the service heat element, verify that the resistance values are within the specified range. Refer to the following table:

Range

Description

Less than 5 ohms

Seat Back Cushion Ctr Element

Seat Back Inner/Outer Element

Seat Cushion Ctr Element

Seat Cushion Inner/Outer Element

Between 850 ohms and 11.5 K ohms

Seat Cushion Ctr Thermistor

Important: DO NOT attempt to remove the factory heat elements from the seat trim cover. The service heat element is to be installed between the existing factory heat element and the seat trim cover.

1st Design Front Seat Cushion Trim Cover-Inside Out ( 1st Design Rear, 2nd and 3rd Design Front/Rear Similar)
Object Number: 1322922 Size: SH
  1. Remove the trim cover with the non-functioning heat element. Refer to the appropriate seat trim cover removal procedure in the Seats sub-section of the Service Manual.
  2. Place the seat trim cover on a clean flat surface with the inside facing out.
  3. Remove the wiring harness from ONLY the non-functioning factory heat element. Use a pair of diagonal side cutters to cut the harness wires as close to the factory heat element material as possible.
    4. • If installing a center heat element, go to Step 4.
    • If installing an inner or outer heat element, go to Step 6.

    Object Number: 1323007 Size: MF

    Important: DO NOT start the cut with a jab or poke.

  4. If installing a center heat element, create an opening between the non-functioning factory heat element (1) and the seat trim cover as close to the seam (2) as possible. Use a razor blade or an equivalent sharp tool and carefully slice through the factory heat element until a hole is created.
    5. • Insert your finger(s) through the hole and lift the center heat element material (1) away from the trim cover material.
    • Use scissors and/or a razor blade to cut the center heat element material along the entire length of the seam (2) from corner to corner.

    Object Number: 1326566 Size: MF
  5. Insert the service heat element (5), with the backing paper side up, between the trim cover material and the factory heat element material (6).
    6. • Ensure the service heat element is laying flat, is tucked into each corner and extends to each side.
    • Carefully remove the backing paper from the service heat element.

    Object Number: 1322986 Size: SH
  6. If installing an inner or outer heat element, create an opening (4) in the middle of the factory heat element (3). Use a razor blade or an equivalent sharp tool and carefully slice through the factory heat element until a hole is created.
    7. • Insert your finger(s) through the hole and lift the inner/outer heat element material (3) away from the trim cover material.
    • Use scissors and/or a razor blade to create a 20 to 25 cm (8 to 10 inch) opening (4) in the middle of the factory heat element.

    Object Number: 1326567 Size: SH
  7. Insert the inner or outer heat element (8), with the backing paper side up, between the trim cover material and the factory heat element material (7).
    8. • Ensure the service heat element is laying flat, is tucked into each corner and extends to each side.
    • Carefully remove the backing paper from the service heat element.
  8. Use 3M® Highland Cloth Duct Tape, P/N 06969, or equivalent, to cover the opening.
  9. On trim covers with three heat elements, connect the inner and outer heat element 2-way white connectors to the center heat element harness.
  10. Install the seat trim cover. Refer to the appropriate seat trim cover installation procedure in the Seats sub-section of the Service Manual.
  11. Assemble the seat assembly.
  12. Place the seat assembly inside the vehicle. DO NOT install at this time.
  13. Verify the seat heat function is operational.
  14. Complete the seat assembly installation. Refer to the appropriate seat replacement procedure in the Seats sub-section of the Service Manual.

Parts Information

1st Design - For 1998 - 2000 Vehicles Built BEFORE VIN YU204670

Part Number

Description

25755073

Heater Pkg-F/Seat Back Cushion-LH

25762972

Heater Pkg-F/Seat Back Cushion-RH

25755076

Heater Pkg-F/Seat Cushion-LH/RH

25755082

Heater Pkg-R/Seat Back Cushion-LH

25762973

Heater Pkg-R/Seat Back Cushion-RH

25755085

Heater Pkg-R/Seat Cushion-LH

25762974

Heater Pkg-R/Seat Cushion-RH

2nd Design - For 2000 Vehicles Built AFTER VIN YU204669 to 2001 Vehicles Built BEFORE VIN 1U228114

Part Number

Description

25755074

Heater Pkg-F/Seat Back Cushion-LH/RH

25755077

Heater Pkg-F/Seat Cushion-LH/RH

25755083

Heater Pkg-R/Seat Back Cushion-LH/RH

25755086

Heater Pkg-R/Seat Cushion-LH

25762975

Heater Pkg-R/Seat Cushion-RH

3rd Design - For 2001 Vehicles Built AFTER VIN 1U228113 thru 2004 MY

Part Number

Description

25755075

Heater Pkg-F/Seat Back Cushion-LH/RH

25755078

Heater Pkg-F/Seat Cushion-LH/RH

25755084

Heater Pkg-R/Seat Back Cushion-LH/RH

25755087

Heater Pkg-R/Seat Cushion-LH/RH

Parts are currently available from GMSPO.

Warranty Information

For vehicles repaired under warranty, use:

Labor Operation

Description

Labor Time

C7340*

RH F/Seat Cushion Heated Seat Component Heating Element-Install

1.1 hr

ADD

Diagnosis Time

0.0-0.3 hr

C7341*

RH F/Seat Back Cushion Heated Seat Component Heating Element-Install

1.5 hr

ADD

Diagnosis Time

0.0-0.3 hr

C7342*

LH F/Seat Cushion Heated Seat Component Heating Element-Install

1.1 hr

ADD

Diagnosis Time

0.0-0.3 hr

C7343*

LH F/Seat Back Cushion Heated Seat Component Heating Element-Install

1.5 hr

ADD

Diagnosis Time

0.0-0.3 hr

C7344*

RH R/Seat Cushion Heated Seat Component Heating Element-Install

0.9 hr

ADD

Diagnosis Time

0.0-0.3 hr

C7345*

RH R/Seat Back Cushion Heated Seat Component Heating Element-Install

1.0 hr

ADD

Diagnosis Time

0.0-0.3 hr

C7346*

LH R/Seat Cushion Heated Seat Component Heating Element-Install

0.9 hr

ADD

Diagnosis Time

0.0-0.3 hr

C7347*

LH R/Seat Back Cushion Heated Seat Component Heating Element-Install

1.0 hr

ADD

Diagnosis Time

0.0-0.3 hr

*This labor operation is new and will be included in the next update of the Labor Time Guide.