GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 1999 🢒 Seville 🢒 Body and Accessories 🢒 Wiring Systems 🢒 Electronic Brake Control Module Replacement

Removal Procedure

    Object Number: 332507 Size: SH

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
  2. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls - 4.6L.
  3. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

    4. Important: The EBTCM cannot be repaired. If faulty, replace the EBTCM as an assembly.

  4. Remove the 3 EBTCM/BPMV assembly bracket nuts.
  5. Remove the EBTCM electrical connector.
  6. Remove the front insulator and insulator mounting bolt.
  7. Remove the 4 EBTCM to BPMV bolts.

    8. Object Number: 143452 Size: SH

    Caution: Do not pry the EBTCM from the BPMV as damage to the seal may result.

  8. Separate the EBTCM from the BPMV by gently pulling forward until separated. Be careful not to damage the seal.

Installation Procedure

    Object Number: 143452 Size: SH
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Clean the seal and BPMV gasket surface with alcohol.

    3. Object Number: 332507 Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the EBTCM to the BPMV.

    4. Tighten

        • Tighten the 4 mounting bolts to 4.5 N·m (40 lb in).
        • Tighten the insulator bolt to 14 N·m (124 lb in).
  4. Install the 3 EBTCM/BPMV assembly bracket nuts.

    5. Tighten
    Tighten the bracket nuts to 9 N·m (80 lb in).


    Object Number: 332509 Size: SH
  5. Install the EBTCM electrical connector. Ensure that the EBTCM connector tab is locked down.
  6. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls - 4.6L.

    7. Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  7. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.

    8. Important: When replacing the EBTCM, Magna Steer® must be recalibrated. Refer to Variable Effort Steering Programming in Steering.

  8. Perform the ABS Diagnostic System Check. Refer to Diagnostic System Check - ABS .