GM Service Manual Online
For 1990-2009 cars only

Special Tools

J 39544-KIT Complete Torque Socket Set - 10 Pieces

Removal Procedure

    Caution: Use care when positioning the tire and wheel assembly on the tire changer. The upper/lower bead breaker or tire changing tools may damage the TPM sensor. To prevent damage, position the valve stem/sensor 90 degrees away from the two bead breakers. For rim clip tire changers, position the bead breakers approximately 180 degrees away from the valve stem/sensor.

    Note: This vehicle is equipped with tire and wheel assemblies specific to the front and rear axles. Ensure that the correct tire and wheel assembly is installed on the corresponding axle.

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.

  2. Object Number: 656803  Size: SH
  3. Remove the wheel center cap, if equipped.
  4. Remove the wheel nut caps, if equipped.
  5. Mark the relationship of the wheel to the hub.
  6. Remove the wheel nuts.
  7. Warning: If penetrating oil gets on the vertical surfaces between the wheel and the rotor or drum it could cause the wheel to work loose as the vehicle is driven, resulting in loss of control and an injury accident.

    Caution: Removing the wheel may be difficult because of foreign materials or a tight fit between the wheel and the hub/rotor. Slightly tap the tire side wall with a rubber mallet in order to remove the wheel. Failure to follow these instructions may result in damage to the wheel.

  8. Remove the tire and wheel assembly from the vehicle. If the tire and wheel assembly is difficult to remove, perform the following steps:
  9. 6.1. Install and tighten all wheel nuts on the affected wheel.
    6.2. Loosen each wheel nut 2 turns.
    6.3. Lower the vehicle.
    6.4. Rock the vehicle from side to side.
    6.5. Repeat this procedure if necessary.
  10. If the tire and wheel assembly still does not loosen, perform the following steps:
  11. 7.1. Start the engine.
    7.2. Drive the vehicle forward and rearward slightly while applying quick, hard jabs of the brakes prior to changing direction.
    7.3. Repeat this procedure, if necessary.

Installation Procedure


    Object Number: 656803  Size: SH

    Warning: Before installing the wheels, remove any buildup of corrosion on the wheel mounting surface and brake drum or disc mounting surface by scraping and wire brushing. Installing wheels with poor metal-to-metal contact at the mounting surfaces can cause wheel nuts to loosen. This can cause a wheel to come off when the vehicle is moving, causing loss of control and possibly personal injury.

    Note: If the vehicle is equipped with directional tread tires, ensure that the directional arrow on the outboard side of the tire is pointed in the direction of forward tire rotation prior to installation on the vehicle.

  1. Remove any corrosion or foreign material from the wheel and the hub mounting surfaces.
  2. Clean the threads on the wheel studs and wheel nuts.
  3. Align the reference mark and install the tire and wheel assembly to the hub.

  4. Object Number: 156809  Size: SH
  5. Install the wheel nuts.
  6. Caution: Refer to Fastener Caution in the Preface section.

    Caution: A torque wrench or J 39544 must be used to ensure that wheel nuts are tightened to specification. Never use lubricants or penetrating fluids on wheel stud, nuts, or mounting surfaces, as this can raise the actual torque on the nut without a corresponding torque reading on the torque wrench. Wheel nuts, studs, and mounting surfaces must be clean and dry. Failure to follow these instructions could result in wheel, nut, and/or stud damage.

    Note: Tighten the nuts evenly and alternately in order to avoid excessive runout of the tire and wheel assembly.

  7. Using the J 39544-KIT , tighten the wheel nuts in the appropriate sequence shown and tighten to 140 N·m (100 lb ft).
  8. Install the wheel nut caps, if equipped.
  9. Install the wheel center cap, if equipped.
  10. Lower the vehicle.
  11. Perform the tire pressure sensor learn procedure. Refer to Tire Pressure Sensor Learn.