| Table 1: | Rear Integration Module Scan Tool Data Parameters |
| Table 2: | Rear Integration Module Scan Tool Output Controls |
Parameter | System State | Expected Value | Description |
|---|---|---|---|
Operating Conditions: Ignition ON | |||
Ambient Light Status | -- | Day | The scan tool displays Night or Day. |
Auto. Trans. Equipped | -- | Varies | The scan tool displays Yes or No. Yes is displayed if automatic transmission is equipped on the vehicle. |
Backup Lamp Relay Cmd. | -- | Off | The scan tool displays On or Off. This is the state of the backup lamp relay. |
Battery Disconnect | -- | No | The scan tool displays Yes or No. Yes is displayed if the battery was reconnected when the alarm was triggered. |
Battery Voltage Signal | -- | Varies | This displays Volts. This is the current battery voltage signal. |
BPP Circuit Signal | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the brake pedal position (BPP) circuit signal. |
Courtesy Lamp Dimming Status | -- | Varies | The scan tool displays Fade On, Fade Off, On or Off. |
Courtesy Lamp PWM Cmd. | -- | Varies | This displays %. |
Courtesy Lamp Status | -- | Varies | The scan tool displays Off, Manual, Manual Defeat, Door Open, Door Closed, Exit, RFA, RFA Theft, Air Bag or Panic. |
CTD Status | -- | Varies | The scan tool displays Disarmed, Alarm Inhibit, Arming, Armed, Alarm or Disabled. This is the state of the content theft deterrent system. |
Hood Ajar | -- | No | The scan tool displays Yes or No. Yes is displayed if the hood was open when the alarm was triggered. |
Hood Closed Switch | -- | Active | The scan tool displays Active or Inactive. This is the state of the hood closed switch. |
Hood Open Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the hood open switch. |
Ignition Cycle Counter | -- | Varies | This displays Counts. This is the ignition cycle counter measured in counts. |
Inadvertent Power Cmd. | -- | Varies | The scan tool displays Active or Inactive. |
Inadvertent Power Input | -- | Active | The scan tool displays Active or Inactive. |
Inclination Sensor | -- | No | The scan tool displays Yes or No. Yes is displayed if the inclination sensor was triggered. |
Inclination Sensor | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the inclination sensor. |
Inclination Sensor Enabled | -- | Inactive | The scan tool displays Yes or No. Yes is displayed if the inclination sensor is enabled. |
Inclination Sensor Status | -- | Inactive | The scan tool displays Valid or Invalid. This is the status of the inclination sensor. |
Intrusion Sensor | -- | No | The scan tool displays Yes or No. Yes is displayed if the instrusion sensor was triggered. |
Intrusion Sensor | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the intrusion sensor. |
Intrusion Sensor Enabled | -- | No | The scan tool displays Yes or No. Yes is displayed if the intrusion sensor is enabled. |
Intrusion Sensor Status | -- | Valid | The scan tool displays Valid or Invalid. This is the status of the intrusion sensor. |
Left Front Door Open Sw. | -- | No | The scan tool displays Yes or No. Yes is displayed if the driver front door was open when the alarm was triggered. |
Left Rear Door Jamb Sw. | -- | No | The scan tool displays Yes or No. Yes is displayed if the driver rear door was open when the alarm was triggered. |
LF Turn/Hazard Lamp Command | -- | Off | The scan tool displays On or Off. This is the state of the driver front turn / hazard lamp. |
LR Turn/Hazard Lamp Command | -- | Off | The scan tool displays On or Off. This is the state of the driver rear turn / hazard lamp. |
Park Brake Relay -- A | -- | Off | The scan tool displays On or Off. This is the state of the park brake relay-A. |
Park Brake Relay -- B | -- | Off | The scan tool displays On or Off. This is the state of the park brake relay-B. |
Rear Compartment Lid Ajar | -- | No | The scan tool displays Yes or No. Yes is displayed if the rear compartment lid was open when the alarm was triggered. |
Rear Compartment Lid Ajar | -- | Closed | The scan tool displays Ajar or Closed. This is the state of the rear compartment lid. |
Rear Compartment Lid Release Relay | -- | Off | The scan tool displays On or Off. This is the state of the rear compartment lid release relay. |
Rear Defog Load Shed 1 Status | -- | Varies | The scan tool displays Active or Inactive. |
Rear Defog Load Shed 2 Status | -- | Varies | The scan tool displays Active or Inactive. |
Rear Defog Load Shed 3 Status | -- | Varies | The scan tool displays Active or Inactive. |
Rear Defog Status | -- | Off | The scan tool displays On or Off. This is the state of the rear defogger. |
Rear Fog Lamp Relay Cmd. | -- | Off | The scan tool displays On or Off. This is the state of the rear fog lamp relay. |
Reverse Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the reverse switch. |
Right Front Door Open Sw. | -- | No | The scan tool displays Yes or No. Yes is displayed if the passenger front door was open when the alarm was triggered. |
Right Rear Door Open Sw. | -- | No | The scan tool displays Yes or No. Yes is displayed if the passenger rear door was open when the alarm was triggered. |
RF Turn/Hazard Lamp Command | -- | Off | The scan tool displays On or Off. This is the state of the passenger front turn / hazard lamp. |
RPA Chime Signal | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the rear parking aid chime. |
RPA Status | -- | Normal | The scan tool displays Normal, Level 1, Level 2 or Level 3. This is the state of the rear parking aid. |
RR Turn/Hazard Lamp Command | -- | Off | The scan tool displays On or Off. This is the state of the passenger rear turn / hazard lamp. |
Run/Crank Terminal Status | -- | Active | The scan tool displays Active or Inactive. This is the state of the run/crank terminal. |
Standing Lamp Relay Cmd. | -- | Off | The scan tool displays On or Off. This is the state of the standing lamp relay. |
Sunroof Enable Command | -- | Varies | The scan tool displays Enable or Disabled. |
Theft Deterrent Alarm Status | -- | Disarm | The scan tool displays Arm, Blip, Armed or Disarm. |
Triggers Per Theft Cycle | -- | Varies | This displays a numeric value. This is the number of alarm triggers per theft cycle. |
Scan Tool Output Control | Description |
|---|---|
Courtesy Lamp 1, 2 w/dim | The RIM activates the courtesy lamps for 15 seconds when you select ON. The courtesy lamps will turn off through the theater dimming feature if you select OFF before the 15 second period has elapsed. |
Courtesy Lamp 1, 2 w/o dim | The RIM activates the courtesy lamps for 5 seconds when you select ON. The courtesy lamps will turn off immediately if you select OFF before the 5 second period has elapsed. |
Inadvertent Power Relay | The RIM deactivates the inadvertent power for 5 seconds when you select OFF. The interior lamps should be inoperative for 5 seconds. |
Interior Lamp Relay | This output control is used to command the interior lamp relay on and off. |
Intrusion Sensor | This function allows you to enable the vehicles intrusion sensors. |
LF Turn/Hazard Lamp | The RIM activates the left front turn/hazard lamps for 5 seconds when you select ON. The left front turn/hazard lamps should illuminate for 5 seconds. |
LR Turn/Hazard Lamp | The RIM activates the left rear turn/hazard lamps for 5 seconds when you select ON. The left rear turn/hazard lamps should illuminate for 5 seconds. |
RAP Relay | This output control is used to command the RAP relay on and off. |
Rear Defog Relay | This output control is used to command the rear defogger relay on and off. |
Rear Fog Lamp Relay | The RIM activates the rear fog lamp relay for 5 seconds when you select ON. The rear fog lamps should illuminate for 5 seconds. |
Reverse Lamp Relay | The rear integration module (RIM) activates the reverse lamp relay for 5 seconds when you select ON. The reverse lamps should illuminate for 5 seconds. |
RF Turn/Hazard Lamp | The RIM activates the right front turn/hazard lamps for 5 seconds when you select ON. The right front turn/hazard lamps should illuminate for 5 seconds. |
RR Turn/Hazard Lamp | The RIM activates the right rear turn/hazard lamps for 5 seconds when you select ON. The right rear turn/hazard lamps should illuminate for 5 seconds. |
Secure Vehicle | This function allows the user to control the vehicle theft deterrent. |
Trunk Release Relay | This output control is used to command the trunk release relay. |
